Search results

  1. S

    17" Jeep Wheel Question

    Jeep are 5x4.5 bolt pattern so you would have to have an adapter or have the hubs and axles redrilled
  2. S

    Got some Taurus fans for my 96 Tahoe. Should I run both or just one?

    I got the electric fans off a Ford Taurus from our local Pull a Part. I have seen people take one and mount it in the fan shroud but I didn't know if I need to figure out a way to mount both if they will fit. If I need to use both should I try and build some sort of shroud or just mount them...
  3. S

    0411 ECU swap questions

    To the people that have done the 0411 ecu swap how much did you gain and how aggressive did you go with the tune? We are going to do my swap really soon and I am wondering what to expect, how aggressive we can go on what fuel for the most gains, and to what RPM should spin the motor to?
  4. S

    96 K2500 Suburban 454 dyno run

    I know this thread is older but I was looking for updates on the turbo and if you were able to dyno it after the tune and 0411 ecu swap.
  5. S

    GMT400 Master Cylinder swap issue, need help ASAP

    I am unclear what happened. Me and a friend fought like hell trying to get it in gear and couldn't. My wife comes home and first try straight in gear. If you're on the fence about this upgrade I highly recommend it. I did the 8600 lbs GVWR calipers, 1/2 ton pads and rotors and a 2000 Silverado...
  6. S

    GMT400 Master Cylinder swap issue, need help ASAP

    I have a 1996 Chevrolet Tahoe that I just replaced all the brake components with new parts. 3/4 ton calipers, rotors, pads, drums, wheel cylinders, shoes, and a 2000 Master Cylinder. We got everything changed out, bled and ready to go. But when we went to leave the house to bed the brakes in it...
  7. S

    Will 96 4WD wheel bearings bolt in later model spindles

    I have a 1996 Tahoe 4WD that I am lowering and building like a sport truck. I was wanting to upgrade the brakes and lower it more. I wanted to see if I could bolt on a 2" drop spindle from a 2000 model truck, then put on the 14" brakes from a 2010 model and use the 96 model wheel bearings or if...
  8. S

    96 Tahoe AC issue/need to know what to replace and what can be upgraded

    Is there a compressor that will work with the L31 and a Gen III or Gen IV if I end up going LS. I would hate to spend the money replacing my AC parts and possibly having to change parts again
  9. S

    Under drive pulley and electric fans

    I am about to replace all my AC components and was thinking it would be a good time to replace my engine driven fan with electric and put on an under drive pulley. In Alabama it gets 100° frequently so I want the best fans possible. All the cooling system is new from the hoses to thermostat to...
  10. S

    Questions on a spindle swap to get a 4WD 96 Tahoe much lower

    That's the plan, I think the tapper of the ball joint on the GMT800 spindle has to be changed. But my goal was to do it to get another 2" drop with correct suspension geometry and ability to swap to bigger better brakes. People have been putting Z06 brakes on GMT800 for a while, I think some...
  11. S

    Questions on a spindle swap to get a 4WD 96 Tahoe much lower

    I have a 4wd Tahoe that currently has lowering keys for a GMT800 and shackles. I want to know if anyone here has put a drop spindle from a GMT800 on and what it took. My plans are spindles, coil overs to ditch the torsion bars, hangers for the back along with my shackles and a notch. I also want...
  12. S

    96 Tahoe AC issue/need to know what to replace and what can be upgraded

    I was told that there was a Ford orifice tube that was some sort of upgrade. I didn't know if I could get a compressor for a different vehicle that uses the Vortec 5.7 that would work better. Since the truck doesn't have rear AC I am looking for anything possible to improve the cooling.
  13. S

    96 Tahoe AC issue/need to know what to replace and what can be upgraded

    My wife has a 96 Tahoe that recently the clutch stopped engaging on the compressor. You can manually tap it to engage it but it won't last. My question is, I want to know what to replace, what can be upgraded, and what are worthwhile upgrades to do with the front end apart. Like taking off the...

Latest posts

Staff online

Members online

Total: 485 (members: 13, guests: 472)

Forum statistics

Threads
64,706
Messages
1,399,186
Members
52,279
Latest member
Crossingover89

Share this page

Top