Recent content by tooturntdad
-
Difference between 94-98 Chevy and GMC Corner lights?
Oh right on that second link is the ones I was looking for. I guess doing the general search with “buy now” slimmed the listings down to the ones I found vs bidding. Yep! Fell in love with the look for a hot minute. Im taking the bow tie out and fitting a bel air emblem. yeah theyre nice. if I...- tooturntdad
- Post #21
- Forum: Paint / Body / Detailing
-
Difference between 94-98 Chevy and GMC Corner lights?
Hate to dig this up again. 2 questions. Are the headlights and signals the same for the gmc trucks vs chevy? I really like my projectors as they dont have the crappy halos. Searched forever for these. Also anyone got a link for all clear corners for the gmc grille? I dont like amber or the thin...- tooturntdad
- Post #17
- Forum: Paint / Body / Detailing
-
Part number help!
Haha too late. I ended up getting #4 in #2 i reassembled everything to get it to move into my garage boy was she not happy. The retainer clip broke so when I pushed it in to what I thought clipped in it went all the way in. My own ignorance. I guess its time to pull the head to get it out. Got...- tooturntdad
- Post #7
- Forum: Engine Performance + Maintenance
-
Part number help!
96 tahoe 5.7 And now Im dealing with an injector being pushed in too far on the spider. My luck Now to figure out how to get it out without panicking- tooturntdad
- Post #3
- Forum: Engine Performance + Maintenance
-
Part number help!
Was in the process of replacing my fuel pressure regulator and I snapped the small plastic line that runs from firewall on the passenger side to what I believe is another sensor of some sort over by the TPS. I think is vacuum related Im not entirely sure. I just know its old and as I was trying...- tooturntdad
- Thread
- Replies: 6
- Forum: Engine Performance + Maintenance
-
Fan Clutch help
Haha yeah Im from Knoxville as well. Belt is on the pulley and everything seems fine. But nah I never did send the oe in for the core. The oe failed as it would legit spin freely and temps were fluctuating. Tried bleeding the system thinking I had an air pocket after the inlet hose retainer clip...- tooturntdad
- Post #3
- Forum: Engine Performance + Maintenance
-
Fan Clutch help
Probably obvious answer for a “dumb” question. Got a fan clutch that bit the dust. Ordered a replacement and sadly was sent the wrong one so Im down without a fan clutch for a few days. Question is, can I still run around without it as I wait for the new one to come in. Current conditions...- tooturntdad
- Thread
- Replies: 11
- Forum: Engine Performance + Maintenance
-
“Lag”?
Alright so I replaced my EGR valve a few days ago and the same code popped back up. So im wondering if this narrows down to a fuel issue maybe? like perhaps my fuel to air ratio is off due to potential bad FPR or clogged filter? i also have a short circuit for both o2 so perhaps maybe im running...- tooturntdad
- Post #24
- Forum: Engine Performance + Maintenance
-
“Lag”?
Now with a leaking injector wouldnt I be able to smell fuel? Because I dont smell any at all.- tooturntdad
- Post #22
- Forum: Engine Performance + Maintenance
-
“Lag”?
Ill get the readings of it when driving here in a bit. Pressure with the key off dropped significantly. Went down 46psi.- tooturntdad
- Post #20
- Forum: Engine Performance + Maintenance
-
“Lag”?
So Im running into fluctuating pressures at idle. Range between 51-55psi. Whats the standard for these trucks? I know the 5.3 gmt800s are at 60psi at idle. Im guessing the 5.7s are about the same?- tooturntdad
- Post #18
- Forum: Engine Performance + Maintenance
-
“Lag”?
Alright. Replaced the wires and the cap and rotor. Same issue occurs. Decided to give it a few revs. Pedal to the floor it bogs at 2800rpm and backfires a little. Half throttle itll rev up to 5000rpm. No CEL. No misfire at idle. No current codes. Going to tackle the fuel filter next. Im...- tooturntdad
- Post #16
- Forum: Engine Performance + Maintenance
-
“Lag”?
Sure know how to break down a paragraph. That “launch control” reference is just what best describes the way it sounds and acts. I come from the rally enthusiast community. Well, motorsport world. Instead of launching a car at start full rev and cause spinning during initial acceleration from a...- tooturntdad
- Post #12
- Forum: Engine Performance + Maintenance
-
“Lag”?
Alright folks! Sorry for being stupid late with an update. So, So far I have replaced my EGR valve and cleared the code and seen a relatively small difference in throttle response. This lasted a few days and then it just wants to bog out on me again under load. Just replaced the plugs tonight...- tooturntdad
- Post #9
- Forum: Engine Performance + Maintenance
-
4 corner mod
Yeah anyone with LEDs in a reflector housing is an absolute ass. though I cant say much. my signals are led with reflector housings. i wish they made those premade ones with white led only cause i hate amber lighting. might just buy a set and rebuild the arrays and make them white but im also...- tooturntdad
- Post #27
- Forum: Audio + Electronics
