Members

JeremyNH

I'm Awesome From Pelham, NH

Joined: Oct 26, 2020

Last seen: Sunday at 11:10 PM

Latest activity Postings About

- J
  
  JeremyNH replied to the thread Problem with temperature gauge.
  
  Something to consider is that the temperature gage and the ECM use different sensors. The ECT to ECM is the two wire sensor near the...
  
  Nov 29, 2023
- J
  
  JeremyNH replied to the thread Need help, where does this 2 wire plug into?.
  
  EVO (electronic variable orifice) only affects power steering. At higher speeds it reduces the hydraulic pressure to the gearbox theory...
  
  Nov 18, 2023
- J
  
  JeremyNH replied to the thread Need help, where does this 2 wire plug into?.
  
  It's the EVO circuit that goes to the back of the PS pump. Given what EVO is and some folks opinions on it it may have been disconnected...
  
  Nov 18, 2023
- J
  
  JeremyNH reacted to SUBURBAN5's post in the thread Mystery plug with Like.
  
  O2 sensor before cat
  
  Nov 15, 2023
- J
  
  JeremyNH replied to the thread Info on 5.7L marine intake swap.
  
  My marine intake came off a 2005 Mercruiser with a 305. I'll list what I did which worked as I've had it on two motors over the last...
  
  Nov 15, 2023
- J
  
  JeremyNH replied to the thread 4l80e Flexplate 3 or 6 bolt?.
  
  7/16 is a substitute for M10 using SAE bolts in flanges with metric holes in most substitution tables. The fastener higher torque of the...
  
  Oct 12, 2023
- J
  
  JeremyNH replied to the thread 4l80e Flexplate 3 or 6 bolt?.
  
  Not for nothing but you don't need six bolts at the TC. Not ever. The bolt circle at the torque converter has pretty much exactly 3...
  
  Oct 12, 2023
- J
  
  JeremyNH replied to the thread 4L80 swap tips and tricks..
  
  I just went to the tune repository. There is only one tune for the 2002 van and it is for a 5.7L/4L80e (1249079920). The 4Lo shift...
  
  Oct 6, 2023
- J
  
  JeremyNH replied to the thread Budget 383 vortec sleeper build..
  
  My stroker uses a Scat 4-350-3800-5700-L (same as the HT383), KB 164-40 pistons, and Eagle CRS6000BST connecting rods for a compression...
  
  Oct 4, 2023
- J
  
  JeremyNH replied to the thread JB Weld on accessory bolt studs in aluminum heads?.
  
  Decided to go with Time-sert. Using a spare 3/8-16 bolt, some white out, and digital calipers I marked exactly 0.501" of thread depth in...
  
  Oct 3, 2023
- J
  
  JeremyNH reacted to L31MaxExpress's post in the thread JB Weld on accessory bolt studs in aluminum heads? with Like.
  
  I will also add that I have run the L31 brackets sans 1 bolt per side before. LT1 I swapped into a TBI truck with TBI on it. The bolt...
  
  Oct 2, 2023
- J
  
  JeremyNH reacted to 454cid's post in the thread JB Weld on accessory bolt studs in aluminum heads? with Like.
  
  If the stud is holding now, would Loctite be enough to keep it in place, without being permanent?
  
  Oct 2, 2023
- J
  
  JeremyNH reacted to L31MaxExpress's post in the thread JB Weld on accessory bolt studs in aluminum heads? with Like.
  
  TImesert or helicoil then put the stud in that hole. Personally I would stud all the holes as I did. Biggest shock I had with a...
  
  Oct 2, 2023
- J
  
  JeremyNH reacted to Hipster's post in the thread JB Weld on accessory bolt studs in aluminum heads? with Like.
  
  Timesert or helicoil. Hokey repairs tend to let loose when you're out in the middle of nowhere.
  
  Oct 2, 2023
- J
  
  JeremyNH reacted to L31MaxExpress's post in the thread JB Weld on accessory bolt studs in aluminum heads? with Like.
  
  I bought the accessory studs that are usually used 1 per head from GM and used them on all the acessory head bolt holes in my van. Saves...
  
  Oct 2, 2023
Show older items
Loading…
Loading…