jdjonesdr's latest activity
-
jdjonesdr replied to the thread Steering column thingy.FWIW... I replaced both the cam and the base thats mounted underneath, an it still wouldn't cancel my left signal. No problem with the... -
Probably, if you can find the software cartridge(s). The Tech1 & Mastertech parts are getting a little thin on the ground. If you have...
-
The RJ12 jack you circled on the back is an RS232 serial port. You can send data to a VT100 terminal or RS232 serial printer. The...
-
I know you said there was no slop in the mounts. How did you inspect? May also have too much play in rear gears. There was also a time...
-
jdjonesdr reacted to movietvet's post in the thread Deceased American Legion member wife's truck with
Like.
Ok, I just talked to her. The a/c was working when she parked it last summer. The heater works. All lights work. The radio may work but... -
jdjonesdr reacted to sewlow's post in the thread Deceased American Legion member wife's truck with Haha.
Shhh...That's supposed 'our' secret! Word gets out & all those rust-belters will be headed here with trailers in tow, buying up all our...
-
jdjonesdr replied to the thread Engine Idles Unevenly and Almost Stalls When Cold.I just checked EBAY and there's one there for $225. That's a good deal.
-
jdjonesdr replied to the thread Engine Idles Unevenly and Almost Stalls When Cold.I have a Bosch 1300 scanner I got on Amazon for a little more than 200 bucks. It's the only Bosch scanner that will scan OBDI systems...
-
jdjonesdr reacted to movietvet's post in the thread Engine Idles Unevenly and Almost Stalls When Cold with Like.
Key word is "supposed". I also believe the penetrant can get past the gasket. That is why I said that I do it over time. I know it is...
-
jdjonesdr reacted to Road Trip's post in the thread Engine Idles Unevenly and Almost Stalls When Cold with Like.
I just found the ALDL physical layout/electrical pinout info in the '94 FSM Electrical & Diagnostic manual. This illustrates what...
-
jdjonesdr reacted to movietvet's post in the thread Engine Idles Unevenly and Almost Stalls When Cold with Like.
You can also use a piece of wire, insulated or not. If insulated, strip the insulation back about 1/2" on each end and then bend the...
-
jdjonesdr reacted to movietvet's post in the thread Engine Idles Unevenly and Almost Stalls When Cold with Like.
You can do it yourself without a scanner/code reader. Just pulling codes that is. Look at you tube but all you need is a paper clip and...
-
jdjonesdr reacted to movietvet's post in the thread Engine Idles Unevenly and Almost Stalls When Cold with Like.
Yes, thermostat is at end of upper radiator hose at engine. Need to attach at least a code reader and see what code(s) is in there. You...
Staff online
-
df2x44L60E Destroyer
Members online
- Nicks2drtahoe
- Srg1016
- Caman96
- Road Trip
- aruffnit
- patrick5050
- 95YardArt
- Sean Buick 76
- SuperSpore
- DR CHOP
- BLK97OBS
- rdobirdman
- RacerM95
- 1990LB
- FLGS400
- Tan1998K2500
- Griffin
- JPVortex
- caw_86
- Brian71583
- Gordy_
- x97k1500x
- Ranger
- JEFF995
- 99xcss4
- Dravec
- Canadian Rust Bucket
- Fireythrash
- Rob93z71
- Chevytruck98
- termite
- vince72
- msmall
- df2x4
- Remodelmaster
- 1998_K1500_Sub
- Stephen schloss
- ZebGMT400
- jman2
- Gezrcrew0406
- 62barsoom
- 0xDEADBEEF
- Idaho83815
- Driven71
- Jk0120
- yevgenievich
- G1kon1wheel
- Ryanstokes8
- Charlesteneows
- roadkill79