Recent content by Green15

  1. Green15

    looking for rear lift options that dont use blocks

    I used 2 " blocks and the U-Bolt Flip Kit from Offroad Design out of Colorado. They have a kit that works that's 11.5" I believe. http://offroaddesign.com
  2. Green15

    Post your lifted 2wd's!

    I would say that it's less less factor of the ride getting softer and more that I am getting used to the new ride quality. Overall, I am very happy with the new setup.
  3. Green15

    LED Gauge Install

    I'm pretty sure it's a NEO T4. I am looking through my old invoices because I originally bought a NEO 3 which was too small, then o ordered a NEO 4 which worked. This is from superbrightleds.com.
  4. Green15

    Post your lifted 2wd's!

    I know it's off topic, but how do you like that light bar? What size did you go with? It looks good!
  5. Green15

    My 95 C1500

    Probably going to need to regear if you jump to either size, especially 35s. Just something to think about when you start budgeting everything out.
  6. Green15

    LED tail lights

    I went through about 3 boards on the OE tails. Definatly love the look of the LEDs. Fingers crossed, these last.
  7. Green15

    Post your lifted 2wd's!

    Here was my truck before the latest work. 4" spindles, no block. 31x10.50s same rims. I could have probably squeezed 32x11.50s like this, people have, people do. After about 5 years of seeing the truck like this, I wanted a little more lift hence the 2" coils and block project I just finished...
  8. Green15

    Post your lifted 2wd's!

    I'll start by saying, I think you're doing things right. I say this because I did things completely out of order. To answer your first question, I went with the 10.50s for a few reasons. 1st: I have 15x7 in. rims. This is too narrow to be recommended for a 12.50. Yes people mount 12.50s on 7...
  9. Green15

    My 95 C1500

    Sweet! I like the plan. I've done most of what your list includes. I ran the 4" spindles with 31s for 5 years and loved it. Well, I just lifted again to fit 33s but like Ruger said above, 31s will look good.
  10. Green15

    Post your lifted 2wd's!

    I emailed Rough Country to ask about their 2" kit combined with the 4" spindles and all they wanted to tell me is that the truck won't align.... so I gave that up and got everything from Canuck for a good price, it's aligned great with the UCAs. Anyways, ~23.75" from rim center to fender.
  11. Green15

    Post your lifted 2wd's!

    It's definatly firm! I will admit, I didn't expect it to be THAT much firmer with the new coils, but it does ride firm. My shocks before were shot so maybe that threw me off for the comparison. Either way, I'm very happy with how the truck turned out.
  12. Green15

    LED tail lights

    Got new tails a few months back. Ended up with Spyders smoked LED tails. I put the LED backup light in myself.
  13. Green15

    Post YOUR Favorite Picture of YOUR Truck!!!

    My new* before and after. *just lifted again! 31x10.50s on top 33x10.50s bottom
  14. Green15

    Post your lifted 2wd's!

    Well, I lifted again! Already had the 4" RC Spindles. Ran 31x10.50s for about 5 years and wanted a little more... Went with Canuck Motorsports' 2" taller coil and 2" block. While at it, went ahead and got Canucks UCAs, put in new upper and lower ball joints and tie rod ends. Out back with...
  15. Green15

    My 99 2dr 2wd Tahoe

    Just read the whole thread, nice project! I've always liked the 2dr. Tahoes. Nice to see it coming along.
See more

Latest posts

Members online

... and 7 more.
Total: 1,829 (members: 57, guests: 1,772)

Forum statistics

Threads
64,469
Messages
1,394,567
Members
51,739
Latest member
huskyninja90

Share this page

Top