Search results

  1. MNZ71

    Post your white 400's

    Day I bought it What it looks like now Sent from my iPhone using Tapatalk
  2. MNZ71

    K1500 on 15x8 rally wheels

    Thanks!
  3. MNZ71

    K1500 on 15x8 rally wheels

    The tires stick out a couple inches on these rims. The rim itself is probably about even with the truck
  4. MNZ71

    K1500 on 15x8 rally wheels

    They stick out about an inch past my flares so they would be roughly 2 inches without flares. That's with 33/12.5 mud terrains.
  5. MNZ71

    K1500 on 15x8 rally wheels

    Doesn't show the wheels real well. I can get get a better pic tomorrow if you want.
  6. MNZ71

    Putting A Chip In A TBI Truck

    I have a jet stage 2 that the po installed. Ive had the truck for almost 30000 miles and always run regular fuel with no ill effects.
  7. MNZ71

    Installing new blend door actuator...Any special things to know?

    The door and the motor are keyed so it can only go on one way. You really cant mess it up.
  8. MNZ71

    2 inch blocks with a crank and 33s?

    2" block and crank to level
  9. MNZ71

    Small black box on frame?

    The pic you posted is a back up alarm so that's what I'd guess is in your truck.
  10. MNZ71

    NO truck yet - NJ

    This ^^^ It may have been made in late 95 but its a 96 model year.
  11. MNZ71

    NO truck yet - NJ

    All 95's were obd1. They switched to obd2 in 96 when they went to the vortech engine.
  12. MNZ71

    Lets see those tools and toolboxes

    I have a Snapon box. Mostly Snapon tools with some Matco in there as well.
  13. MNZ71

    Speaker Write Up

    Ill try to get a pic of my 6x9s in my extended cab tomorrow
  14. MNZ71

    axle shims needed after 2" lift using blocks and crank???

    The shaft should be no more than 3 degrees and both angles should be within 1 degree of each other
  15. MNZ71

    axle shims needed after 2" lift using blocks and crank???

    I have 2 inch non angled blocks on mine. I had the same question about shims so I actually measured my angles and they were still within spec with my 2 inch block without any shims.
  16. MNZ71

    Minnesota Rollcall!!

    We must live pretty close to each other. I live right behind the Harley dealer on highway 23.
  17. MNZ71

    Minnesota Rollcall!!

    I'm from around St. Cloud also.
  18. MNZ71

    Stuck trailer hitch lock

    The one I have you put the key in and keep turning it. The end of the pin screws off as you turn the key. Could be the same? :shrug:
  19. MNZ71

    Which cv shaft?

    Thanks!
  20. MNZ71

    Part Number for these Center Caps?

    I would check junk yards around you. Those wheels are very common. You should be able to find a set really cheap.
  21. MNZ71

    Which cv shaft?

    Truck is a 95 k1500. My left cv shaft makes a popping noise when I turn the wheel all the way at slow speeds. Rock auto lists the shafts with or without an ABS ring. I don't remember the shaft having an ABS ring but it's been a while since i've pulled one out. Anyone know which one I need to...
  22. MNZ71

    Hazards stuck on

    so just the button is broken off? Can you stick a screwdriver or something in there to turn them off?
  23. MNZ71

    Hazards stuck on

    I believe the hazards are controlled internally in the turn signal switch so if you cut the wires for them you would lose your turn signals. I'm not 100% on that though.
  24. MNZ71

    k5 15s on k1500?

    As long as you have the right lugs with the threads on the outside they fit no problem.
  25. MNZ71

    k5 15s on k1500?

    Factory gmt800 caps. They came off of these wheels:

Latest posts

Members online

... and 24 more.
Total: 1,709 (members: 74, guests: 1,635)

Forum statistics

Threads
64,656
Messages
1,398,085
Members
52,157
Latest member
xundying

Share this page

Top