Search results

  1. Terrible03

    No spark, at wits end

    Yes. Covered all that in the original post. The rotor spins, not the cam gear.
  2. Terrible03

    No spark, at wits end

    Well since everything else is working just fine, i ordered another computer off ebay. If it turns out to not be the computer, oh well, i like having one for a spare anyway
  3. Terrible03

    No spark, at wits end

    I plugged mmy computer in to the obd, it read everything just fine.
  4. Terrible03

    No spark, at wits end

    Gotcha. Ill try it out tomorrow
  5. Terrible03

    No spark, at wits end

    How do you do that? The four pin sends and recieves the info to/from computer. If i disconnect it to see if signal is coming, it wont send to begin with.
  6. Terrible03

    No spark, at wits end

    I did check all the connectors. I even bought an analog tester in case my digital was giving bad readings. Voltage and resistance hit all proper readings according to my shop manual.
  7. Terrible03

    No spark, at wits end

    Well i would guess it is getting signal from computer. Computer is fine, power is going to the module, all the wires and connections are good, and the module was tested at napa.
  8. Terrible03

    No spark, at wits end

    Ahhh gotcha. No i replaced the ground from block to firewall
  9. Terrible03

    No spark, at wits end

    I replaced the coil with a spare too, i had a msd coil on it and heard they like to fail, so i replaced things i already had spares for.
  10. Terrible03

    No spark, at wits end

    Its a tbi, coil is outside. I already replaced the dizzy thinking it was the problem because it was old and the pick up was rusted.
  11. Terrible03

    No spark, at wits end

    Ok. 92 k2500, heavy duty type. Was driving down interstate when truck back fired, bucked then died. Got it home, and started diagnistics. Has fuel. No spark at coil. Coil tests good. Distributor, cap, rotor replaced. Tried three different icm's, all good. Checked resistance of pick up...
  12. Terrible03

    Doozy -shifting, stumbling, smoking

    It's not knock sensor. Been runnin fine for a month. This literally came out of no where. Sent from my iPhone using Tapatalk
  13. Terrible03

    Doozy -shifting, stumbling, smoking

    I'm gonna hook it up tomorrow to datamaster and tunerpro. Tps sounds about right. I thought esc also, but I don't think it would affect the trans shifting. Sent from my iPhone using Tapatalk
  14. Terrible03

    Doozy -shifting, stumbling, smoking

    Ok background first. 92k2500 with a 4l80e. Motor is a 347 with a mild cam, flat tops, roller rockers, 2.02/1.64 valves, carb intake and a 454tb holding 65lb injectors. Burnt my own chip, been running like a dream. It has been throwin that crazy code43 for last couple weeks at least once a...
  15. Terrible03

    Flowtech or Summit shorty headers?

    Wonderful discussion here! My two cents : I'm a long tube fan. Every truck I've owned, first thing I did was put long tubes and straight duals on. BUT, with my 92, I put on shorty headers. Was a lot of thinking involved. What it came down to was the the trucks make AWESOME low range torque...
  16. Terrible03

    Need chip help

    Yup. I'm almost to the point of just payin for a burn. Cuz after all the mods I've done, it won't run right without a tune Sent from my iPhone using Tapatalk
  17. Terrible03

    Need chip help

    Yeah that's what I'm sayin. All the physical stuff is fine. It's obviously the template, but I've used 3 different ones, all supposedly for my computer, and none worked Sent from my iPhone using Tapatalk
  18. Terrible03

    Need chip help

    So adapter is def fine. And chips are holding the burns. It's def in the data getting burned onto the chip Sent from my iPhone using Tapatalk
  19. Terrible03

    Need chip help

    Yup. All it reads off the stock is limp mode when you use that adapter. Sent from my iPhone using Tapatalk
  20. Terrible03

    Delphi Fuel Injection upgrade

    Headers, programmers, exhaust, cai, all that jazz. Sent from my iPhone using Tapatalk
  21. Terrible03

    Need chip help

    Yup. It's blowing my mind Sent from my iPhone using Tapatalk
  22. Terrible03

    Need chip help

    It's been about 6 months since I messed with it (been rebuilding the engine all winter). I have two adapters, but can't remember which they were. Def the adapters from moates for EPROMs, tho. I got the standard one and the one to run different burns, like the jet 6 pack. The proms were all good...
  23. Terrible03

    Need chip help

    Yeah but they say it's cuz I'm not using the right template. Sent from my iPhone using Tapatalk
  24. Terrible03

    I keep replacing thermostat

    I'd say you're on to somethin with moving the location. Sent from my iPhone using Tapatalk
  25. Terrible03

    I keep replacing thermostat

    Sorry using tapatalk app to read forum, doesn't show signatures. Sent from my iPhone using Tapatalk

Latest posts

Members online

Total: 1,386 (members: 41, guests: 1,345)

Forum statistics

Threads
64,950
Messages
1,403,436
Members
52,817
Latest member
stig

Share this page

Top