Search results

  1. Chevyboy95

    Alternator Bracket/Power Steering Pump Mount 95 C1500 5.7L V8

    On the mount using the DR44 case, using a thick washer or the OEM shim that is on the longer bolt, it directly bolts on and requires no modification outside of the 3rd mount (rear center of the CS144 case) that is on the motor needs to be moved/removed/adjusted to fit the depth of the DR44.
  2. Chevyboy95

    Alternator Bracket/Power Steering Pump Mount 95 C1500 5.7L V8

    Had a couple questions as y'all are definitely more knowledgeable regarding what will and wont fit. The original part number I found for the alternator bracket is 10233233 which is no longer in production. The listed replacement that works for it is 10118701. The link provided i believe in post...
  3. Chevyboy95

    Alternator Bracket/Power Steering Pump Mount 95 C1500 5.7L V8

    It isn’t s a direct fit as the depth hits the 3rd mounting point of the stock alt. That has to be bent or removed. The failure was due to 5-6year of extra stress running dual alternators and a mod to the mounting hole that cracked after low temps sitting in the driveway. Working on making it...
  4. Chevyboy95

    Alternator Bracket/Power Steering Pump Mount 95 C1500 5.7L V8

  5. Chevyboy95

    Alternator Bracket/Power Steering Pump Mount 95 C1500 5.7L V8

    The mount never had issues with it. My issue of the mounting hole cracking was due to some mods to run dual alternators and I opened one of the holes a bit too much. Worked fine for 5-6 years then in the last freeze here in Texas, it cracked.
  6. Chevyboy95

    Alternator Bracket/Power Steering Pump Mount 95 C1500 5.7L V8

    That is a aftermarket mechman alternator from probably 5-6 years ago. 270a. I used to do a bunch of car audio so the alternators I was using are I the 270-320a range typically. Thanks guys. I’ve been having hell trying to find what would fit the motor as every sites part matcher would only...
  7. Chevyboy95

    Alternator Bracket/Power Steering Pump Mount 95 C1500 5.7L V8

    Trying to find out if there is an official part name for what I am trying to replace. The left alternator mount cracked and want to replace it if I can find the part. It holds the power steering pump and has the power steering pulley on it as well. 1995 C1500 5.7L V8. Any ideas on what it...
  8. Chevyboy95

    The Stupid Engine Questions Thread

    I had a similar issue a few years back, and mine was the distributor not working correctly, and somethign about that 1750-2000rpm range, same as yours would make it really show up. And if I stayed under it or passed it up, it would "behave". Mine never through an error for it I don't believe...
  9. Chevyboy95

    95 Ext Cab Chevy Build

    little more done, had do drill new holes for some of the grommets. the 3/0 isnt grommet-ed because the jacket is SO thick and it wont fit trough the grommets. but my lower back is not liking me right now...
  10. Chevyboy95

    95 Ext Cab Chevy Build

    New Battery Bank and battery box
  11. Chevyboy95

    95 Ext Cab Chevy Build

    6.5 cubic feet, tuned to 31hz never metered it, but i know it could break a 50 in the mid 40s.. already rebuilding again, not changing much, but new amps, subs, mids.
  12. Chevyboy95

    sub boxes

    You are wrong, sorry, sensitivity of subwoofers is measured at 1khz. When does a car subwoofer ever play 1khz? Never... They play 20-100hz generally. If it a home audio woofer then sensitivity matters a little more since they generally play mid bass frequencies as well.
  13. Chevyboy95

    sub boxes

    When you say 10s and an 8, do you mean 3 woofers at the same time? If so you will be better off with just 2 10s and no 8 since having tens and an 8 could cause some cancellation and loss of out put. Secondly, 3 subs on 1 amp being 2 channel or 1 gives you mixed ohm loads/ irregular ohm loads...
  14. Chevyboy95

    95 Ext Cab Chevy Build

    and here is a new pic of what my system will consist of after i get the new mids in the new kicks and console.
  15. Chevyboy95

    95 Ext Cab Chevy Build

    thank you randall for telling me to test fit.... would have been bad if i didnt staple where i stapled. Driver side clears the Parking brake by about .25in and the passenger side will probably end up snug on the A/C/Heater thing below my dash. got a TON of sanding and bondo to do though to make...
  16. Chevyboy95

    95 Ext Cab Chevy Build

    Test fitted the driver side kick and needed to staple down some of the fleece to clear the parking brake. Layed down the resin on the driver side kick and it is pretty much cured, then i need to start the sanding and such on it and resin the passenger side one after i test fit it.
  17. Chevyboy95

    95 Ext Cab Chevy Build

    Here is a bit of what it looks like as far as the system. need to do the last trim piece on the top of the loading wall. aaaaaaaaaaaaaaaaaaaand! started my first set of kicks today! dont mind the trash, was consolidating all my audio boxes, card board cut outs, school papers, etc to...
  18. Chevyboy95

    95 Ext Cab Chevy Build

    I left a little gap in pics that were on my phone, finally got around to it. Nothing special, just the amp install mainly. Still stuff i want to redo, the whole figuring out better ways to do something the more you do it. I want to do a new console with more curves and cleaner since i have had...
  19. Chevyboy95

    sub boxes

    i didnt read the first 5 pages but ill post what i think should go accordingly with what i saw skimming. Partical board and wafer board are one of the worst things you can use to make a subwoofer box due to structural and density issues which are both needed for this application. Both those...
  20. Chevyboy95

    Yet another rear speaker question

    I feel like it would be hard to put speakers under the seat without it looking completely ghetto. If i were you, i would take the rear side panels off, trim the stock hole out a bit and mount a 5.25" coax or midrange into that spot with a adapter ring and a little deadener/mat behind it. I...
  21. Chevyboy95

    The Stupid Electronics Questions Thread

    when mine did it, it just needed a little grease. it got hung up a bit. Take the door panel off and get a look at it. Can only suggest so much with limited info.
  22. Chevyboy95

    audio cost

    If you do it yourself not much at all, cost of wire and not much more. If you get a shop to do it, one, they might not do a job to your standard, two, they will charge you for their wire price most likely which is extremely expensive, and three, labor fees. I would personally learn to do it...
  23. Chevyboy95

    95 Ext Cab Chevy Build

    both vids have same power (2 2krms amps at 2 ohms) and same box and orientation. newer vid. http://www.youtube.com/watch?v=4sMSnczaEzI
  24. Chevyboy95

    95 Ext Cab Chevy Build

    older video http://www.youtube.com/watch?v=0RBv1q48zz0
  25. Chevyboy95

    95 Ext Cab Chevy Build

    Thanks guys, houston on the SW side

Latest posts

Members online

Total: 470 (members: 16, guests: 454)

Forum statistics

Threads
64,742
Messages
1,399,741
Members
52,347
Latest member
aces90

Share this page

Top