Search results

  1. A

    Can I see y’all’s x pipe setups?

    About to fab my own stainless 3” exhaust for my rcsb with a lq9. Just wanted some inspiration before I jumped into it
  2. A

    Dropping fuel pressure during a pull

    Alright, hopefully a relatively simple issue. I’ve got a 95 gmc with a lq9 and some bolt ons, 706 heads, and Texas speed cam. For the fueling it has a quantum 255 in the stock sending unit, -6an lines to a c5 vette filter/regulator, and 50 lb injectors. I’ll be doing a pull and I’ll hit around...
  3. A

    3/4” or bigger clutch master cylinder?

    Hey guys, got a lq9 and a tko600 in my 95. Went with the ram 78131 throw out bearing and used my stock master cylinder. Turns out I need a 3/4” or bigger bore in the master cylinder and the stock one is .700”. Clutch pedal feels perfect it just doesn’t go push the bearing in far enough to...
  4. A

    Vss for a tko600?

    It’s a 95
  5. A

    Vss for a tko600?

    Hey guys. Just scored a tko600 with 6k miles on it for a grand. I’m quite excited as this is a pretty big upgrade over the nv3500. How should I go about connecting the vss? It would be cool to have the original speedometer/odometer to work. I’m not really sure where to start.
  6. A

    Fuel pump is turning but not delivering fuel

    I just put gas in it so it hasn’t sat with any in the tank. Not really sure what you mean by submersion. The rubber line on the pump is new and rated for ethanol. Rest of the lines are stainless braided. It’s a 20 gallon tank with roughly 6 gallons. Gauge is reading an 1/8 tank if that helps
  7. A

    Fuel pump is turning but not delivering fuel

    I’ve got a quantum 255 in my stock sending unit. It’s got brand new everything fuel system wise. Filter, pump, lines, filter, etc. I can hear the fuel pump running but no fuel is coming out of the line straight off the sending unit. I’m not really sure why. I’ve got my terminator x relay...
  8. A

    I screwed up

    I may have found one. I can get it for $100 shipped but the only thing is it’s for a auto trans. I don’t think there’s any difference for my application since I’m tearing all the engine/trans stuff out of it.
  9. A

    95 wiring harness interchangeablility?

    I’ve got a 95 c1500 with the manual. I chopped up the original harness trying to do my own Ls swap harness and just ended up getting terminator x. I found a harness out of a 95 2wd with the auto trans. Will it work in place of the manual harness? Motor and trans are no longer in the equation so...
  10. A

    I screwed up

    I wish I could. Middle Tennessee doesn’t seem to have a single 95 in a junkyard ;(
  11. A

    I screwed up

    I’ve got a 95 Sierra 2wd manual that I’m in the process of dropping an lq9 in. I was originally going to chop up the lq9 harness and merge it with the original harness. Started cutting into it and realized I was in over my head and I’d save money on tunes in the future with Holley. Well I’ve got...
  12. A

    Budget caliper brackets?

    I’ve been working on finishing my 6.0 swap. Here in the next few weeks I’ll try to get to it.
  13. A

    Dodge internals in a Chevy nv3500?

    Hey guys, more transmission questions. I’ve been on the hunt for a internal slave nv3500. I got one that the guy said only needed an input shaft. Pull it apart and buddy shredded 2nd gear. I then had a lightbulb moment, my uncle has a 2nd gen dodge rotting on my farm. Are the internals...
  14. A

    Making an external slave work with a Ls?

    Checked it out and they were successful. Only issue is that I can barely weld steel and do not have a tig welder lol. I’m in welding school atm so I might postpone this till I start tig. I’m watching fb market place like a hawk for an internal slave trans.
  15. A

    Making an external slave work with a Ls?

    Over the past few months I’ve been swapping an lq9 into my 95. Finally got to where I thought I was really close just to bolt up the trans and have the slave cylinder interfere with the oil pan. So now I’m at a crossroads, either swap in a 96+ nv3500, convert mine to internal, or go to a t56...
  16. A

    Budget caliper brackets?

    They are the same thickness according to rock auto. I have also seen that awd Astro vans have rotors that could possibly fit. Going to the junkyard tomorrow to get a set to compare to the camaro rotors.
  17. A

    Budget caliper brackets?

  18. A

    Budget caliper brackets?

    Quick update. Got calipers and brackets off a 97 v6 camaro. The bore on the brackets are slightly smaller on the camaro brackets compared to the diameter of my axle. Parking brake stuff on the caliper hits the leafs so that’ll have to get removed. Going to get 95 impala rotors to try out. Only...
  19. A

    Budget caliper brackets?

    I’ll be using impala ss rotors. Sorry forgot to add that. I’ll be getting camaro caliper brackets and calipers
  20. A

    Budget caliper brackets?

    I’ve done a nbs hydroboost and master cylinder swap. Took the proportioning valve off the nbs truck as well. Also swapped to hd calipers up front. I’m looking into taking the whole rear brake setup from a 4th gen camaro so a budget set up might be possible. Going to the junkyard tomorrow to...
  21. A

    Budget caliper brackets?

    Hey guys, I’m on the hunt for a set of caliper brackets to swap my rear drums to discs. I’d like to use my original front caliper but the only brackets I can find are the Cunningham machine and $130 is super steep just for a bracket. I’m open to going to a different caliper but if I can use mine...
  22. A

    Fitting a 15x9.5 -.75 on a 5/7 drop?

    Also truck doesn’t have fender wells bc I got tired of rubbing the stocks too much lol. So that won’t be an issue
  23. A

    Fitting a 15x9.5 -.75 on a 5/7 drop?

    Hey guys, I recently snagged a set of aero wheels off a local nascar team for $70. I’m kind of going for a budget nascar inspired build so it was a no brainer to pick them up. They fit perfectly in the back but the front is where I run into issues. They poke about a 3/8 in out. I’ve got drop...
  24. A

    95 Bulkhead connector on the firewall pin out?

    I looked through it and found the connector. The thing is nothing matches up with my connector. For instance a8 is labeled as battery feed when it’s the starter signal on mine :/
  25. A

    95 Bulkhead connector on the firewall pin out?

    I can’t seem to find the pin out for the bulkhead. I can find 96+ but nothing before that. I would chase wires from the original harness but my dumbass cut a lot of them thinking I didn’t need them. It’s the last part I have to hookup to my Ls stand-alone harness.

Latest posts

Members online

... and 10 more.
Total: 1,819 (members: 60, guests: 1,759)

Forum statistics

Threads
64,494
Messages
1,395,175
Members
51,817
Latest member
Clevis208

Share this page

Top