Search results

  1. Z71_Zimmerly

    Limp mode, PRNDL fuse hot, no power to 4L60E

    Hey guys, I'm stumped on this one. 1998 K1500, 4L60E in limp mode. High idle, won't shift from 3rd. It was intermittently doing this a few times in the last couple weeks, but seems to be stuck in limp mode now. P0740 - TCC enable solenoid circuit electrical P0785 - 3/2 shift solenoid circuit...
  2. Z71_Zimmerly

    Fuel gauge upside down

    I thought I read about this somewhere. I posted last week regarding my fuel needle just hanging. No reply, but understandable. Well, after awhile I realized the guage is reading completely upside down. Literally. At a full tank, it is at the 8:00 position, half tank is at 6:00, empty tank is...
  3. Z71_Zimmerly

    Fuel Gauge needle is hanging

    Hey guys, Looked for a similar topic, couldn't find anyone with this issue. At random while in park, my fuel guage needle completely fell to the (almost) 6:00 position. Is my cluster completely broken? I plan to pull the cover off to reset the needle, but I'm wondering if I'd be wasting my time...
  4. Z71_Zimmerly

    P0338, CKP Sensor replaced, no start

    Well, she's up and running! As I was hoping, she was just severely flooded. I pulled the fuel pump relay, cranked and cranked, she backfired a handful of times before finally starting up. It blew the inner insulation board of my garage door to smithereens. She's running like a dream. I ran her...
  5. Z71_Zimmerly

    P0338, CKP Sensor replaced, no start

    Referring to the Passlock, that would be a great thought indeed. Being well-versed in the Passlock system itself, I can say that isn't the issue, as I don't have a security light on. If it were the passlock, it would also start but shut off immediately. (Been through this twice, lol) Thanks...
  6. Z71_Zimmerly

    P0338, CKP Sensor replaced, no start

    Not sure if you saw my last post in time. Dipstick smells like fuel. I did intake gasket last yr so cam retard is good. Now I'm wondering how screwed I am with fuel in the pan. Thanks
  7. Z71_Zimmerly

    P0338, CKP Sensor replaced, no start

    I just checked the dipstick. Oil smells like fuel. Haven't flooded like this before. Am I screwed? What should I do next? Thanks again for your help
  8. Z71_Zimmerly

    P0338, CKP Sensor replaced, no start

    I think throttle is fine, I will double check. Fuel pump is sounding fine to me on prime. Didn't think there'd be live data, since no start, but will take a look.
  9. Z71_Zimmerly

    P0338, CKP Sensor replaced, no start

    After replacing it, I cleared the code. I tried starting a few more times, and the code hasn't popped back up. The thing is, I don't know how long this code was stored. I replaced my distributor last year and went through dialing-in the cam retard offset, and thinking about it, I don't know if...
  10. Z71_Zimmerly

    P0338, CKP Sensor replaced, no start

    98 K1500. Truck ran great. Stored it in my cold garage for Winter. Started it a month ago for 30min. No problem. Went out to start today, cranks and cranks, gives a chug once in awhile, no start. Checked codes, got P0338 for crankshaft position sensor circuit high. Pulled sensor, noticed it was...
  11. Z71_Zimmerly

    U-bolt application for stock

    Just an update, all went well. The top plates worked just fine too. Thanks guys
  12. Z71_Zimmerly

    Ignition Timing Apps/PIDs

    For those of you who have set Vortec timing with a bluetooth app after replacing their distributor: I know this topic has been touched upon, but I'm looking for some more detailed information. 5.7 Vortec - '98 K1500 I replaced my distributor correctly, and the engine is running well. I just...
  13. Z71_Zimmerly

    U-bolt application for stock

    Well, I was able to find those saddles at a local salvage yard. Now, my only question is, can I use the same top spring plate from my 10 bolt? I'm keeping my 1/2 ton springs, just swapping rear axle assemblys.
  14. Z71_Zimmerly

    U-bolt application for stock

    Thanks Schurkey. Had no chance of getting anything else from the donor vehicle- the rest of it was scrapped before I bought the rear end. I'm assuming my top plate will work for this new axle? Would anyone else happen to know of a part number, or at least measurements for the 9.5 SF carrier...
  15. Z71_Zimmerly

    U-bolt application for stock

    Sorry, I have a '98 K1500 ext cab, stock 10b 3.42... The replacement rear end is the 14b 3.42 9.5" with the G80 locker, posi. It was pulled from a salvage yard, and was originally in a '97 K1500 ext cab, with the F44 package.
  16. Z71_Zimmerly

    U-bolt application for stock

    Wow, I figured this was a long forgotten thread, it's nice to have such a quick response. I finally found the u-bolts I need, by searching by VIN of the mysterious donor vehicle. It was a 1/2 ton ext cab, like mine. I plan on keeping my leaf springs, at least for now. Problem now is, I need the...
  17. Z71_Zimmerly

    U-bolt application for stock

    I'm doing a 10b to 14b swap myself. (3.42, 9.5" ring gear) Beside diameter, would you guys happen to know the rest of the u-bolt/plate specs? Having a hard time getting a straight answer anywhere else. This community has helped me a lot throughout this build, but this is my first time posting...

Latest posts

Staff online

Members online

... and 6 more.
Total: 1,608 (members: 56, guests: 1,552)

Forum statistics

Threads
64,525
Messages
1,395,901
Members
51,911
Latest member
Fireythrash

Share this page

Top