JPVortex's latest activity
-
JPVortex replied to the thread Bad running after manual swap.Ok thank you. I did keep my automatic computer, I wonder if this is the problem. For my 94 truck, which year of computers will work? If... -
JPVortex replied to the thread Bad running after manual swap.I did not replace the spring for the regulator, but it looked to be in fantastic shape still, i dont think that's an issue. I do agree...
-
JPVortex replied to the thread Bad running after manual swap.So update here, did a fuel pressure test and this is the result in the video below. Seems low to me. The pump is not even a year old, so...
-
JPVortex replied to the thread Bad running after manual swap.What’s also weird is here and there it’ll idle perfectly but then I’ll shut it down and start it, then it starts idling bad again
-
JPVortex replied to the thread Bad running after manual swap.Yeah I sprayed brake clean all over all the sources of vacuum, rpm’s didn’t change at all at any spot, unfortunately I don’t have a...
-
JPVortex replied to the thread Bad running after manual swap.So I have totally thrown the parts canon at it this afternoon. I replaced the PCV Valve, IAC, MAP sensor, cap & rotor. No difference at...
-
Hello y’all, just recently finished swapping in a 5lm60 to my 94 k1500 with a 350 tbi. It runs great off idle, but at idle it runs...
-
JPVortex replied to the thread 94 5 speed swap slave & master.Ok so I am a little worried here. I think I got all the air out of the system but just pressing the clutch it doesn’t really feel like...
-
JPVortex replied to the thread 94 5 speed swap slave & master.THANK YOU for this!!! Was having a terrible time bleeding the system today. Tried the 2 person method and gravity bleeding, still had...
-
JPVortex replied to the thread Nv3500/5lm60 cracked case.I know nobody that can weld this thing, and I have never touched a welder in my life. Chances are once I have some money saved up Im...
-
JPVortex replied to the thread Nv3500/5lm60 cracked case.I just don’t know it’s worth the time or money to get welded, it was a $200 transmission.
-
JPVortex replied to the thread Nv3500/5lm60 cracked case.It looked a little worn to me, still round but there was just a couple scores on it.
-
JPVortex replied to the thread Nv3500/5lm60 cracked case.Was going to replace it just for safe measure, definitely not cast into place it’s pressed in. But the replacement I got is wrong...
-
JPVortex replied to the thread Nv3500/5lm60 cracked case.Lmao, jb weld is just a safe measure. I’m pretty sure there was still enough material in the hole for the stud that it is secured...
-
JPVortex replied to the thread Nv3500/5lm60 cracked case.I got the pivot stud pressed back in, there was enough material in there to get it pressed back in. Not sure if it’ll hold, but I’m...
Members online
- Das Hatt
- markariaobs
- Feral peasant
- wb292
- Suburban7148
- aldang25879
- Peavey
- G R G
- 305_champ
- 99xcss4
- Mwzo6
- BuiltToWork
- T3B3
- jaywestfall
- Flynssr
- JAngeli
- Pomper05
- bc-chris
- BNielsen
- Motrhedx81
- Ghostman
- ldaggerl
- deadweight
- David Kinter
- rdobirdman
- jay g
- robertlee
- PlayingWithTBI
- RamonRdzS
- 454cid
- bryanv0721
- 0xDEADBEEF
- 95burban
- Mellio2
- Gobo
- alexwalters08
- JDGMC
- Boomer50
- Tiger joe
- Silveradhoe
- gwolf
- Remodelmaster
- HemiDeuce
- Kinglazard
- gijoe3922003
- majack82
- fancyTBI
- BeXtreme
- L31MaxExpress
- Danimal08