Recent content by jasons99hoe

  1. jasons99hoe

    First bagged build, have some questions

    i agree 100% with you. i cant remember how many times i was worried about a situation and it worked out very well once i got to that point. YAMAHA17 you will be fine. you have way more tools than most guys i have seen do their first bag job. one thing i will note is the biggest pain in the...
  2. jasons99hoe

    Choosing exhaust system

    thats how i did my system but i did a single 3" i used a dynomax bullet
  3. jasons99hoe

    Long tubes? Or short?

    it was for the front o2 sensor not the rears. gotta have the fronts
  4. jasons99hoe

    Twin Subs, 1999 K1500 and C1500

    dont ever go to the metal unless you have too. just feather out any hard lines and edges and make sure its scuffed and VERY clean before paint. you will see all the dents and dings once you paint it.
  5. jasons99hoe

    Twin Subs, 1999 K1500 and C1500

    very good point. i had to do it to mine from lowering it so much
  6. jasons99hoe

    Long tubes? Or short?

    thats what i did. they cut one short and gave it a small turn and it cleared the cross member. it was close on the driver side. when using the patriots they didnt have an o2 bung on passenger side so i had them put one in at the collector adapter because i didnt want them to mess up my...
  7. jasons99hoe

    Long tubes? Or short?

    mine is a tahoe 4 door. thats probly the difference but if im correct the trans crossmember is in the same spot as your if its a 2wd 4l60e. sorry it didnt work out for you. i get compliments all the time.
  8. jasons99hoe

    Long tubes? Or short?

    if your truck is 2 wheel drive then go with the patriot h8059. i did them and they work PERFECT. no cutting no bending no hammering NO modification at all. passenger side is snug getting in place but just shove it in and done. i will post pictures when im at home as i dont have the pictures...
  9. jasons99hoe

    Steering box options

    i will look into that if i need to but luckil makes sense. i have seen it a few times. i was thinking more about the quick ratio vs stock turn ratio. but i totally see the bennefit of removing slop. i could see it helping with 4 wheeling tho
  10. jasons99hoe

    Intro

    welcome.
  11. jasons99hoe

    How bad are clearance problems with a 5/7 drop?

    thats why i specified tahoe. they sit a little different.
  12. jasons99hoe

    Steering box options

    why change steering box? stock works fine.
  13. jasons99hoe

    How bad are clearance problems with a 5/7 drop?

    i am 5/7 in a tahoe and i have no issues. i used stock springs instead of the drop springs. flip kit in rear. had to clearance a cross member for drive shaft ( its a tahoe). i did the bolt in notch but i welded it and it felt better afterwards. im on 245/40/20 and it has no clearance issues
  14. jasons99hoe

    MPFI spider injector swap/upgrade info and questions thread

    you can do it. if your nervous about all the electrical connections just take pictures and tape each connection and label them with numbers. the biggest mistake i see is people missing a plug and not sealing down the upper intake. its a simple job just a tedious one. give yourself ample time...
  15. jasons99hoe

    Help me diagnose a rough idle condition that is driving me crazy

    see how much play you have in distributor. i see alot of distributor gears severly worn. just something to check. seems to me like a timing issue
See more

Latest posts

Members online

... and 17 more.
Total: 2,001 (members: 67, guests: 1,934)

Forum statistics

Threads
64,465
Messages
1,394,690
Members
51,728
Latest member
Car_Guy_YYC

Share this page

Top