Recent content by Helomedic1171

  1. H

    NBS Front Brake Swap for OBS Trucks

    Aligned just fine. Here's the spec sheet.
  2. H

    NBS Front Brake Swap for OBS Trucks

    I didn't because I know the GMT900 brakes work. Once I have proof of concept, then I can get wilder with it. Also, I would have to run spacers or get new wheels, and I just don't want to do either. I may swap in the future, but not right now.
  3. H

    NBS Front Brake Swap for OBS Trucks

    My LCAs were Delphi TC6239 and TC6241 Application: 2000 Chevrolet 2500 6.0
  4. H

    NBS Front Brake Swap for OBS Trucks

    Parts mostly look right to me except I didn't used lower arms meant for Mexican-market trucks. I used ones from a 2000 GMT800 2500. I'll dig out the part numbers in a sec. Also, I used Mevotech bearings. They come with the bolts already so you save money there. They also have the hub surfaces...
  5. H

    NBS Front Brake Swap for OBS Trucks

    My fitting is a 3/8-24. I took the old GMT400 hose as well as the new GMT800 with me to verify. Mine thread on and off just fine. With everything connected, no leaks.
  6. H

    NBS Front Brake Swap for OBS Trucks

    2000 Chevy 2500 (GMT800) arm Yes, the Ball Joint hole. I reamed the top one only. Thanks for pointing these out, I edited my post above. I'll be going for an alignment next week once I finish the brakes and doing a rear wheel seal. I work long hours and only get weekends to work on it right now.
  7. H

    NBS Front Brake Swap for OBS Trucks

    Here's my photos. In these photos, I still need to hang rotors and pads, but the swap is essentially done. I'll have completed photos later this week. Notes: I did NOT ream the bottom hole, I used new LCAs from a 2000 Chevy 2500 (GMT800). They are drop forged, come with the ball joint and...
  8. H

    NBS Front Brake Swap for OBS Trucks

    As an update to this thread - I can add some photos of my swap if that would be helpful. I also wrote down some party numbers of things I used like the brake line adapter and the stainless steel braided hoses.
  9. H

    NBS Front Brake Swap for OBS Trucks

    If you're talking about a 2wd, I don't think anyone does. Honestly, I don't think anyone sells pre-modified spindles for this swap at all.
  10. H

    NBS steering components in a 400

    Can confirm; I swapped in the GMT800 box, hydroboost, and the steering shaft. Only had to modify the shaft a bit, basically eliminated the rag joint on my truck with the bottom half of the 800 shaft and the top half of the 400 shaft. A Cherokee (WJ) shaft would also work, that's what I had...
  11. H

    13" NBS rear disc on 14 bolt SF

    Anyone had a problem with the rotors from the NBS brakes not seating all the way down on the 14bsf axle flanges?
  12. H

    4l60e to 4l80e conversion article from Four Wheeler

    I have a 5.3 and 4L80E I'm swapping into a 98 K1500 ECSB - anyone know if I can keep my stock drive shafts by moving the engine forward? of so, by how much? or which mounts did you use (besides the Dingo mounts)
  13. H

    GMT 400 Hydroboost swap

    if you can find it - I wound up going with a GMT800 setup for my 98 K1500. it takes modification here and there, it is not a bolt-in, but it isn't as hard as solid axle swap. I used parts from a 2004 Suburban with HB, and got the HB unit and the hose from the HB unit to the gear box. I also...
  14. H

    NBS Front Brake Swap for OBS Trucks

    I've done it, several others have or are doing it. Go check out FSC, there are threads on it. It's pretty doable.
  15. H

    NBS Front Brake Swap for OBS Trucks

    You HAD to ream the bottom hole? I thought it was the same size as the LBJ on the OBS trucks. I tested mine with an OBS LBJ and it didn't need reaming. Sent from my XT1080 using Tapatalk
See more

Latest posts

Staff online

Members online

... and 19 more.
Total: 1,963 (members: 69, guests: 1,894)

Forum statistics

Threads
64,455
Messages
1,394,383
Members
51,704
Latest member
Hectormtz

Share this page

Top