Recent content by Axewhlder

  1. A

    What size bolts are needed for the rear bumper on my 95 K1500?

    Being that I've never taken or put on a rear bumper on one of these trucks will the 22 pc bolt kit work? Thanks again..
  2. A

    What size bolts are needed for the rear bumper on my 95 K1500?

    I bought my truck and it had a roll pan on it. I can't stand it. Today I picked up a used rear bumper but it didn't include any of the bolts. Does anyone know what size and type of hardware I'll need to mount the bumper to the body? Thanks.
  3. A

    1991 Silverado. 4wd pops out of gear when trans is in 1st gear. (5 spd)

    Good to know. Thanks for the response.
  4. A

    1991 Silverado. 4wd pops out of gear when trans is in 1st gear. (5 spd)

    Guys - I'm looking to purchase a 91 K1500. Its a 5spd 4x4. The guys says it pops out of 4wd when he puts it in gear. I havent looked at the truck yet but I'm trying to get an idea what I'm in for. I just sold my 97 because of 4wd gremlins and would had to buy another issue. Thanks in advance.
  5. A

    Driver's side CV Shaft replacement

    Thanks as always for the help guys. I'll be doing it this week.
  6. A

    Driver's side CV Shaft replacement

    "Vatozone" hahah. Nice. So nothing else needs to be loosened or moved to get the axle out? Thanks for the input.
  7. A

    Driver's side CV Shaft replacement

    Mine is busted and spewing crap everywhere. Anyway, any tricks before I dive into it? Basically, take off the wheel, loosen the nut, break the axle loose from the hub and loosen the retaining bolts. Is there anything else I need to disconnect? Also, what size is the retaining nut on the...
  8. A

    1997 GMC 1500 4WD won't engage and just blinks

    That would be great. A friend of mine is supposed to help me out in a few days with this. Any extra information is always a help. Thank you.
  9. A

    1997 GMC 1500 4WD won't engage and just blinks

    I found something similar to that. I guess my question now is where do I get a diag 13 pin connector? Is that something I can get and plug into the laptop and download a program? As stated I totally suck troubleshooting electrical stuff. haha
  10. A

    1997 GMC 1500 4WD won't engage and just blinks

    How would I go about checking the actual 4x4 switch on the dash to see if it's good or not? From what I've been reading these can go bad and cause the problem as well. Thanks.
  11. A

    1997 GMC 1500 4WD won't engage and just blinks

    I did that first. Fuses are fine. Only ones I checked are on the side of the dash. Any other fuses hidden I should look for?
  12. A

    1997 GMC 1500 4WD won't engage and just blinks

    Just an update - No power to the leads going to the actuator. Is that part of the main engine harness or is it a separate wire that can be disconnected? I followed the wires but they dissapear into the firewall and I have no idea where they end.
  13. A

    1997 GMC 1500 4WD won't engage and just blinks

    Great..electrical stuff.. my favorite. Any suggestion on where I should start? Any brittle points on the T-case as far as harnesses?
  14. A

    1997 GMC 1500 4WD won't engage and just blinks

    Eh, just interested in fixing the problem at hand. I want to get this truck running 100% before I consider putting any cash into it that I don't need to. haha
  15. A

    1997 GMC 1500 4WD won't engage and just blinks

    Also, when it isn't engaged the drive shaft will spin freely by hand. If I engage it then the D/S locks so the t-case should be good. I pulled the dash and the 4wd buttons and the connections seemed good. Are there vacuum lines or anything that can be affecting this?
See more

Latest posts

Staff online

Members online

... and 15 more.
Total: 1,881 (members: 65, guests: 1,816)

Forum statistics

Threads
64,490
Messages
1,395,126
Members
51,811
Latest member
hillbilly269

Share this page

Top