Search results

  1. 9

    Factory style running boards for 2 door Tahoe ?

    Im in Michigan about 20 minutes outside of Detroit
  2. 9

    5.3 4l60e LS to TBI swap help!

    My swap was in a 96 which is a little different as far as controlling the trans is concerned so this may not be accurate for your application "but" there will be a wire coming out of the LS pcm that you will splice into a wire coming out of your factory pcm for the speedo to receive the signal...
  3. 9

    Factory style running boards for 2 door Tahoe ?

    Where can I find factory style running boards for a 96 2 door Tahoe ?
  4. 9

    Wiring questions : Temp gauge and tach

    Anybody ? I figured out the temp sending unit for the gauge it's the 1 wire sender in the head just in case someone else stumbles across this during a search. There has to be someone on this forum with a working tach who can tell me where in the engine compartment I can find the wire or if I...
  5. 9

    Wiring questions : Temp gauge and tach

    Got my engine swapped in (2005 5.3 into 96 Tahoe) and its running just need to finish up on some wiring now. Got 2 questions, which temp sender is for the temp gauge on the dash, the 1 wire sender that was in the 5.7 head or the 2 wire that was in the thermostat housing ? Then where do i tap in...
  6. 9

    Corvette style regulator / filter question

    hey do i use the same 3/8 fitting you have listed to connect to the intake fuel rail ? and do you know if one of these is better than the other dorman 800-121 & dorman 800-082. got the part number for the metal one off ls1truck
  7. 9

    Corvette style regulator / filter question

    Oh I got my pedal in over the weekend, will post some pics in the other thread soon.
  8. 9

    Corvette style regulator / filter question

    Thanks for all the help !
  9. 9

    Corvette style regulator / filter question

    Ok guess the only thing I need to know now is what fittings you used to connect to the return and feed at the sending unit
  10. 9

    Corvette style regulator / filter question

    Hey will my stock feed line from my tank to current filter screw into the corvette filter ?
  11. 9

    Corvette style regulator / filter question

    Ok guess I was just confused because I'm used to speaking in terms of inside diameter when it comes to fuel lines and there are measured in outside diameters.
  12. 9

    Corvette style regulator / filter question

    That's the one I asked about in the post above. 3/8 is the outer diameter but the inner is 5/16, you used this as your feed or return line, or both ?
  13. 9

    Corvette style regulator / filter question

    From where and what size line did you use
  14. 9

    Anybody have DBW in their truck ?

    What did you have to do to the DBW pedal to make it fit, could you post some pics ? Thanks
  15. 9

    Corvette style regulator / filter question

    Also looking at this on summit the hose comes in (3/8 OD - 5/16 ID) and (5/16 OD - 1/4 ID) are these the sizes i need ? I was assuming 3/8 ID was needed for feed and 5/16 ID was needed for return. Thanks
  16. 9

    Corvette style regulator / filter question

    That kit is expensive, do i need the included tool to make lines ?
  17. 9

    Oil and Temp sending unit thread sizes ?

    Need to know the thread size of the oil pressure and coolant temp sending units for the gauges on a 1996 5.7 Vortec for my project.
  18. 9

    Anybody have DBW in their truck ?

    already have the pedal and module that came with my engine, dont want to buy another unless its absolutely necessary.
  19. 9

    Anybody have DBW in their truck ?

    Looking for some pics and ideas of how to modify a DBW pedal to fit in a OBS truck.
  20. 9

    Corvette style regulator / filter question

    How do i go about connecting the feed and return from a Corvette style regulator / filter back to the stock fuel lines on my 96 Tahoe ? Are guys just using injection rated hose and clamps ?
  21. 9

    Fuel rail question

    Gathering parts for a 5.3 swap in my 96 Tahoe and had a question regarding the fuel line/ rail. My factory fuel system has return and feed lines, the engine i purchased just has a feed line. To ease instillation is it possible that i can just swap out my fuel rail with an earlier rail that has...
  22. 9

    Torsion key lift question

    I was under the impression that if I used aftermarket keys since they have more of a built in lift on them it would put less tension on the torsion bar and give me a better ride ? Im new to this so please correct me if im wrong ( here to learn )
  23. 9

    Torsion key lift question

    If i use torsion keys to lift the front of my 96 Tahoe about 2'' do i need shock extenders or shoul i be ok ?
  24. 9

    LS Swap Parts: What to get, and what to avoid.

    Wire harness: Nelson Performance out of Texas makes a nice harnesses for swaps. You can mod one yourself easily buy following instructions at lt1swap.com. You can mod a Vortec V8 harness pretty easy by cutting off the injector harness plug, soldering the correct connectors on and adding 10 wires...
  25. 9

    33 12.5 20 ?

    I'm thinking about running with this size tire and a 20x10 wheel and was wondering what backspace and offset wheel I would need, also what would I need to do suspension wise, would a leveling kit be enough ? This would be going on a 96 2 door Tahoe 4x4. Would like to see some pics if anybody has...

Latest posts

Members online

Total: 1,168 (members: 18, guests: 1,150)

Forum statistics

Threads
64,504
Messages
1,395,351
Members
51,845
Latest member
GMACGMC

Share this page

Top