Search results

  1. Daniel907

    Potential Bad Ground

    Just an update for those so if someone comes across a similar problem in the future. If you truck experiences issues like I did. Be patient and do your proper diagnostics at the beginning so you can eliminate items that will not be a problem. Granted I purchased another vehicle for a daily...
  2. Daniel907

    Potential Bad Ground

    Additional Update: The truck died last Thursday on the way to work. I have been trying my best to brainstorm what may go wrong, and I came up with Ignition Control Module as well, as symptoms are similar. Replaced it, and no go. So yesterday I dropped the tank and replaced the entire sending...
  3. Daniel907

    Potential Bad Ground

    Update. Truck started up no problem this morning, and ran for a good half hour with no issues. Wipers are functioning properly and all the grounds seemed to check out. The only one that may be questionable is the one on the firewall for the ECU. So hopefully I don't encounter this issue...
  4. Daniel907

    Potential Bad Ground

    Thanks for the locations everyone. I know for sure the battery terminals are fine. I looked those over within the past two months. I'll look through all the grounds and see if I can find an issue. I have a feeling it may be one of the metal grounds going from frame to block/evaporator. Living...
  5. Daniel907

    Potential Bad Ground

    Hello everyone, If this is in the wrong section let me know and I will create a thread in the appropriate section. Here is the issue. The truck is acting funny, started it this morning, and it died after about 10 minutes. The truck would not start again right away. After 5 minutes, it started...
  6. Daniel907

    -8AN or -6AN Fuel Line

    True. I'm also trying to anticipate further modifications in the future, which is why the thought of braided lines sprung to mind.
  7. Daniel907

    -8AN or -6AN Fuel Line

    Hey everyone, 92 K2500, TBI 350 4x4 So the front fuel line on my truck sprung a bit of a leak, which I have come to determine is in the rubber hose. I would rather replace the old hose with AN fittings and braided hose, than pay the $100.00 each for the Dorman replacements at the parts store...
  8. Daniel907

    The Offroad Wheel and Tire Thread

    I run a 265/75/16 on my pickup. Had to raise the front ride height just a touch to account for bumps at full lock. But other than that no issues.
  9. Daniel907

    Best drop in bedliner?

    Why not go for a roll on bedliner, like Herculiner?
  10. Daniel907

    350 TBI is all but done for, so....

    Thats all on you, you could spend the extra money and buy the supplies to learn, and tune yourself. You could find someone local, or even through a tuner like TBI chips (I have no experience or preference for TBI Chips, just the first name that came to mind).
  11. Daniel907

    350 TBI is all but done for, so....

    A big block will be nice to throw in there, but 99'Subourbon laid out a pretty nice price list. Which is reasonable without a doubt, except maybe an Edelbrock performer RPM or Air Gap instead of the Victor Jr., which would more practical as a daily. If you enjoy doing the work, you could find...
  12. Daniel907

    Need New Tires.

    I have a new set of BFG A/T KO2's and the do well in the snow, and surprisingly well on ice, far grippier than expected. Plus the more aggressive sidewall is shweeeet!
  13. Daniel907

    94 c1500 computer tuning questions

    I'm pretty sure that 94 is still OBDI, so learn to burn chips, or swap to a dynamic EFI ECM so you don't have to burn chips anymore. Devs93 thread "Ultimate Toolbox 88-98 ( http://www.gmt400.com/threads/the-ultimate-88-98-performance-toolbox.12428/ ) will explain much of what you are asking...
  14. Daniel907

    Need Moar Loud

    Got some videos. The first is when I just put glasspacks onto the true duals about two years ago. https://youtu.be/GQOCjKv0XMM Here is the current setup that I described earlier. I only went to about 3,000 rpm in this one. Don't want to be too inconsiderate to the neighbors...
  15. Daniel907

    Need Moar Loud

    white_trash88, a set of headers and a decent dual setup will make a world of difference. When I first started tinkering with my exhaust, I first just cut off the stock muffler. Later I put on long tube headers with about 16" of 2.5" ID pipe afterwards with turndowns. (Stupid Loud) What I...
  16. Daniel907

    Future build ideas. Input from more experienced users wanted.

    I would hold off on the aftermarket EFI for a few months. At SEMA Holley revealed a new EFI system they will launch in 2016 called the Sniper, uses the same software as the Terminator, but has a self contained ECU within the throttle body. List price is going to be sub- $1000! Thats what I'm...
  17. Daniel907

    Odd Warm up behavior

    Alright, here is the situation. Since the temps have been getting colder at night, since around the beginning of october, the truck has been acting a little funny during its first start of the day. 92 K2500 so you know. The problem is that when the motor is cold, it will start up fine, but...
  18. Daniel907

    Electric fan conversion

    Flex-a-lite has great products. I just installed one of their syclone fans in my truck, as well as the controller unit from Flex-a-lite as well. Works great, and moves a ton of air, and the controller gives you the option of choosing what temperature the fan turns on at.
  19. Daniel907

    97 350, no heat, low temp gauge reading

    I would think thermostat.
  20. Daniel907

    1992 K2500: "You're my boy Blue!"

    A little late than never, but starting a build thread regardless. Bought the truck in February of 2013, after deciding that I would return to Alaska to finish college. (I was living in Prescott, Arizona for school.) I am the second owner, and Original owner took great care of the truck. Only...
  21. Daniel907

    Long tube header questions

    Like Skylark said, Hooker makes a great header. I have a set on my 92 K2500, and there were no major issues installing them. There are two small things you will encounter if you buy them. #1 It can be a pain in the ass tightening the headers to the cylinder head back towards the firewall. There...
  22. Daniel907

    Bushing Suggestions?

    According to the Prothane website, it has Body mounts, front control arms, Spring Pds/ Coll Iso, Steering Bushings and Strut Tower
  23. Daniel907

    Bushing Suggestions?

    Hey everyone, I plan on replacing the bushings all the way round my truck once summer comes. I was thinking this Prothane kit I found on Amazon (http://www.amazon.com/dp/B002P8JVZK/ref=wl_it_dp_o_pC_S_ttl?_encoding=UTF8&colid=67D6D437RUKX&coliid=I33G530AAB18J). Does anyone have any experience...
  24. Daniel907

    best OBD1 scantool?? Misfire/backfire ? at cruising speeds 65-70

    jrollings, does it occur during a specific rpm range? I something similar that happened when I would give it about 3/4 pedal from 55-60 and it just wouldn't go anywhere. I thought it was the fuel pump, but my pops (being the old man he is) took the dizzy apart and found the pickup was corroded...
  25. Daniel907

    Where to put the X for X-pipes.

    Just want to get some opinions. I currently have longtube headers, with 24" glasspacks, true dual. I was a tad bit lazy in the fab work, and decided to dump the pipes just short of the bed. So as you can assume the sound is beginning to become bothersome, and I am considering adding an X, in...

Latest posts

Staff online

Members online

... and 36 more.
Total: 1,844 (members: 86, guests: 1,758)

Forum statistics

Threads
64,510
Messages
1,395,529
Members
51,859
Latest member
joey76122167

Share this page

Top