Recent content by blazin8556

  1. blazin8556

    Throwout bearing won't go on clutch fork!

    Did you get this figured out? I have a throw out bearing that I got with a kit but could not use because I'm doing a 5.3 swap. It's just sitting here if you need it
  2. blazin8556

    going to pick up an old truck

    The truck made it with no problems. Thanks guys
  3. blazin8556

    The Stupid Axle Questions Thread

    Does the cv axle hold the wheel hub together on the front? I don't think it does. The nut just holds the end in right? It's been a minute.
  4. blazin8556

    going to pick up an old truck

    i am going to be going to pick up an older truck soon. its a 95 c1500 with a 4.3 and a 5 speed. it has 250,000 miles on it. i know a failure is a possibility. i am thinking about haveing extra parts for the trip. im thinking water pump alternator distributor wires belt and hoses maybe...
  5. blazin8556

    93 gmc 3500 - Can I swap utility body for regular 8' bed?

    My 2500 had a service body on it, pulled it off and put on a long bed. Later on found the incomplete vehicle sticker on the back wall. I might have just gotten lucky and wound up with a regular truck.
  6. blazin8556

    1990 Complete Overhaul

    came to abrupt halt due to divorce. everything is getting sold off. i do still have an obs. i got a 93 gmc sierra for my daily now. too bad i had big plans for an awesome muscle truck...
  7. blazin8556

    1990 Complete Overhaul

    Had to stop to make some cash for the build. no crank no start intrepid. (cam sensor killed car, owner killed battery and eventually burnt the starter) and now parts are rolling in. 3" front drop springs from stylintrucks.com 2" drop hangers for the rear. truck already had 2" drop...
  8. blazin8556

    1990 Complete Overhaul

    Lift?? cracked open the diff. it was leaning forward on its springs. and i am not kidding. this is how much fluid was in it. none spilled out. open 3:42. no damage to any teeth. i couldn't help it. i had to open the bottom to check. i couldn't figure out the cast numbers.
  9. blazin8556

    1990 Complete Overhaul

    Lets tear down! tear down... all of it.... yep that too... took three of us to beat the passenger door open. one prying, one using a screw driver to push the latch and one to kick from inside getting the old pontoon trailer ready for the cab and bed. no...
  10. blazin8556

    1990 Complete Overhaul

    How i got it...
  11. blazin8556

    1990 Complete Overhaul

    so in the winter/spring of 2014 i peiced together an 87 crx si. long story short i wasn't that happy with it and me being 6'6" i didn't fit in it quite right. very uncomfortable to me. but $20 per week in gas was awesome. even still i put it up for sale. months went by and was offered some crazy...
  12. blazin8556

    The Stupid Electronics Questions Thread

    a/c panel is flashing on my 90. a/c lines have been removed. i can still turn on the blower when it stops flashing and change the blend door. what causes it to flash. never seen this before. the truck has been converted to carb and found that the ecm is missing. is it tied to that?
  13. blazin8556

    Auto to manual 98 Sierra 5.7

    where is the fun in that? your one of those pple that just drive the truck. like my father in law. does it run and drive? yes leave it alone. im one of those pple that can't leave crap alone and want to make it better. if someone wants to build the vehicle i say let him. if they want it to look...
  14. blazin8556

    The Stupid Axle Questions Thread

    is the 85 c20 C&C axle different than a 85 pickup. and if i were to put it in my 98 z71 i know i would have to move mounts and do what else. i can't seem to find some of the threads i once saw on this.
  15. blazin8556

    Forum app discussion

    I have the free tapatalk on my iPhone and iPad. I have noticed that I revive old threads a lot tho..... Like now lol Sent from my iPhone thing
Top