b1jetmech
Latest activity Postings About
-
-
Make it cold enough and it'll freeze over, and you'll have no airflow until you shut the compressor off and let ambient air melt the... -
b1jetmech reacted to 99xcss4's post in the thread TPI set up on 193 heads...will it work? with
Like.
a little expensive but I think it is the only option... -
b1jetmech reacted to 99xcss4's post in the thread TPI set up on 193 heads...will it work? with Like.
beat me to it
-
TPI works great on any stock heads. Honestly I'd stick with the vortecs but you won't be disappointed by the 193s for this application.
-
b1jetmech reacted to Nad_Yvalhosert's post in the thread TPI set up on 193 heads...will it work? with Like.
Ahh. Then I will pay close attention to this thread as I'm interested in doing the same injection setup as O.P. on my '95.
-
b1jetmech replied to the thread TPI set up on 193 heads...will it work?.The TPI will actually raise the peak torque rpm? I would think the 193 heads would offset that. I do want to use a fuel injection...
-
-
b1jetmech reacted to L31MaxExpress's post in the thread TPI set up on 193 heads...will it work? with Like.
If you want your torque at ~3,200 rpm the TPI works well. Under 2,500 rpm a good dual plane manifold will make more torque.
-
b1jetmech posted the thread TPI set up on 193 heads...will it work? in Engine Performance + Maintenance.I'm planning on a high torque small block build to pull my 12K fifth wheel camper. I'm not ready to give on the small block for they are...
-
b1jetmech reacted to Erik the Awful's post in the thread How to Put a Vortec Motor in a TBI Truck with Like.
"Can I swap a Vortec motor in place of my TBI motor and does it just bolt in place?" Yes, you can swap a Vortec motor in place of a TBI...
-
PSI 8.8 is the next best thing to a diesel but the TPI 400 should run well. Mercruiser marine dual plane MPFI intake makes more low-end...
-
Ok our project 6.6L Duramax Gas engine conversion was a success... Ok we jokingly call it a Duramax because it’s probably the closest...
-
b1jetmech reacted to HotWheelsBurban's post in the thread Steve, my 1995 K1500 Cowboy Cadillac. with Like.
Well, the Burb we used to have was converted when you could still buy all the parts from the dealer. Built in 75,when the Burb was brand...
-
-
Loading…
-
Loading…
Members online
- ZacMoto
- termite
- Caman96
- fancyTBI
- TonyM
- Misterman
- Robsez65
- Superdave587
- INW-Iron-Steel
- JDGMC
- big56
- BoolAidMan11
- 0xDEADBEEF
- jackmp18
- Crawlblind
- GMTAS400
- Bobabooie
- CrustyJunker
- Alex26
- hot_rod4
- mse3065
- PlayingWithTBI
- Green1998
- SNCTMPL
- DieselTech
- Burban Driver
- fisher
- Griffin
- BBslider001
- bc-chris
- Arnes98
- kiyiya
- pops84c10
- studigggs
- jgreen16
- burgundybeast97
- 92HotWheelsMan
- Moparmat2000
- Skymedic
- shidychevy
- caw_86
- 95burban
- Gomeszach
- 77lassie
- LukeTheDrifter
- Road Trip
- Dravec
- Scooterwrench
- JollyCaptain
- gijoe3922003