Search results

  1. B

    Cummins swap Ideas need help

    Ok so im doing a cummins swap, my truck is a 1995 chevy 6.5l 5pseed manual and i need ideas/advice for a intercooler. What is the best way to go. I want to put a 12v in. Got most everything else figured out
  2. B

    HELP WINDOW WITH FLATBED

    I need help asap, we were cutting some stuff off the flatbed of my truck and broke the rear window by mistake.. there is barley any room because of the headache rack and i does the rack need to be cut off the replace the window? thanks
  3. B

    How to install the Prebled system 1995 Chevy diesel???

    OK guys so i cant figure this out.. My haynes book has nothing in it about changing such thing. I blew my master cylinder out and the metal line was so worn it snapped behind the slave. I bought the bled unit in hopes of making it easier, but i cant even find a spot in getting the system around...
  4. B

    Engine too old to Chip?

    in fact, i have only seen 1 350 go that long.. I have seen a neglected 6.2l get 350k.. Was a 82 and i think those had issues compared to the later versions
  5. B

    Engine too old to Chip?

    Justin, my mom does lawn care im sure she has an extra one around somewhere Skylark, Ive been around a few 6.5s, if you treat them right they seem to outlast the truck itself, or in my case, the master cylinder for the clutch :/ then rockauto sends me the wrong part. But anyways, i hope it last...
  6. B

    Engine too old to Chip?

    hey guys my 6.5l diesel just passed 240k, bought it awhile back and i was wondering if i could add a "chip" for some more power and the #9 thingy for more fuel coming in. I have some blowby (as much as my 6.2l diesel has with only 112k) i wanted to know if i could push it without blowing...
  7. B

    PTO install

    Does anyone have any info on Installing a PTO on the nv4500? like what i have to do, where i can get the unit? anything will help
  8. B

    Crank Sensor and no spark

    ok so this is going back a long was to when i dropped my suburbans 5.7l vortec back in after a lovely 3 spun bearing replacement that took up a good part of my summer, So my suburban was making this load grinding noise when i turned it over, but when it ran it did nothing. I was asked by a guy...
  9. B

    NEED HELP WONT START

    Figured it out awhile back. I messed up reading out of my book, I set it at the "6" and not the ”8" on the disturber
  10. B

    NEED HELP WONT START

    5.7l vortec 1999
  11. B

    NEED HELP WONT START

    so i am very close to getting my suburban running. It cranks but doesnt want to fire up even the smallest of a cough. useing a multi meter i get a 12 volt charge at the end of my plug wires. What could be wrong? its getting fuel
  12. B

    TBI engine in a vortec

    Is it possible. Can i drop a tbi 350 into my 1999 suburban??
  13. B

    New Engine ZZ4

    So i have a chance to buy a ZZ4 coming out from a boat. Will this match up to my stock 5.7l Vortec?
  14. B

    Ring grove size

    can anyone tell my what my ring groove size is on a stock chevy 350 vortec 2 bolt main from a 1999 chevy k1500 4wd
  15. B

    New engine

    I am looking to get a used engine for my 1999 suburban that has a bad block thanks to a spun main bearing. Can i put a TBI motor with vortec heads in? will it match up?
  16. B

    Maybe the Dumbest Transmission Question on earth.

    Im pulling a engine on my Suburban (1999 k1500 5.7l 4l60e). There are bolts that hold the Converter to the Flex plate (i hope thats the right term) I have to remove them before i disconnect the Engine Right?
  17. B

    pulling an engine, need help

    Im leaving the tranny in. Got a 2ton lift but just didnt want the tranny at the time. Really Close but the top tranny bolts are giving my heck
  18. B

    let's see some pics of your gmt400s

    Stock 1999 k1500 5.7l Vortec With a Main Spun Bearing. Custom 3rd Party Interior With Power 7way Powered driver's Seat. Front seats heated.
  19. B

    Too Much Info

    If i put a 4bolt into a 2bolt Suburban will it match up?
  20. B

    Any swaps?

    Its Got a Spun bearing waiting to get it opened up. Just planning incase my block is grooved. I can get Remanufactured Engines for under that too
  21. B

    Any swaps?

    Its a 1500 but i dont have over $2000 to drop into it right now. Thinking just a stock replacement
  22. B

    Too Much Info

    So ive had 20 different sites tell me 20 Different things about my Engine. It is a 5.7l Vortec from a 1999 Suburban 1500 4x4. Is it a 2 or 4 main bolt or do i have to open it up to tell.
  23. B

    Curious about towing heavy

    Could tow more but brakes and axleshaft/diff, along with springs and everything. Airbags do help with the sagging but don't really rise towing specs do to limits on the axle. Frame is also an thing to look at. I can stick a 454 in my little s10 and tow 10,000lbs but everything else would break
  24. B

    pulling an engine, need help

    Im overhauling the engine. dont need the transmission. So i should pull the Tranny but leave the Transfercase there?
  25. B

    pulling an engine, need help

    I'm pulling the 5.7l Vortec out of my 1999 suburban and i need advice. First time pulling one. Should i pull it with or without the transmission?

Latest posts

Staff online

Members online

... and 27 more.
Total: 2,619 (members: 77, guests: 2,542)

Forum statistics

Threads
64,475
Messages
1,394,704
Members
51,752
Latest member
moverton05

Share this page

Top