Search results

  1. J

    1989 Chevy speedo

    I replaced the TH700R4 in my 89 C1500 with a 4L60E and a Painless Torc transmission controller. Everything is working except, I have no idea how to hook up the speedo. The controller has an output signal (1 wire) but how do I connect it to the speedo? Anyone got an idea how I can have the...
  2. J

    Radiator

    I've got a 34" radiator from a 2007 Silverado that I want to use in my 89 c1500. Just not sure what all the connections are for or where they should go.... The oil cooler and the 2 large connections for the water are obvious but I got 2 smaller connections that I don't know for sure...
  3. J

    multi belt issue

    I'm building a SBC toppped with a Pro Flo XT manifold. The old steel accessories bracket had to go because of the throttle body inlet track and waterneck hitting the back of it. I replace it with later aluminum brackets. OLD NEW (well half of them at least) The issue I'm...
  4. J

    Coil connectors

    Anyone got an idea where I can order online a connector for LS coils? I'm making my own wiring loom and since I live in Europe, it is not so easy to get this from a junk yard. I have no idea of the part number either... Just the numbers on the OEM connector would be helpfull as well!
  5. J

    '89 1500 build thread

    Finally my build thread, I already started last year (actually November 2013) and still not finished.... It is an 89 Chevrolet (although it has a GMC grill), with a ZZ4, th700 and 2wd. It is lowered 2 - 4 and has 17" Boyd Rodders, they need to be polished again... This is my truck when I...
  6. J

    waterneck

    Does anyone know which water neck I could use here? The old one from my TBI engine was too high and hitting the TB and this one is exiting where the alternator is sitting. Which one could I use? :hmm:
  7. J

    bulkhead connector wires on a 96

    I'm installing a 96 dash in an 89 and the bulkhead connector has some extra wires compared to the 89. Does anyone know what the wires on the right side are for?
  8. J

    Installing a 96 dash, connector question

    A while back I picked up a dash that was already pulled from a 96 truck so I could not see for myself where all the connectors were going. Yesterday I started installing it in my truck but got stuck when I couldn't identify some of the connectors. I was said that I got all the wiring that come...
  9. J

    wiring question

    I'm replacing my OBS dash with a one of a '96. I also have all the electrical wiring but got some questions. I see tons of posts of people who already done this before but I'm wondering how they did the steering column and the bulkhead connector. For the steering column, the connector is...
  10. J

    accessories drive bracket

    I have a SBC ZZ4 that I'm converting to EFI with a Pro Flo XT manifold. The issue I have is that my accessories drive bracket is hitting the water neck and it can't be used anymore. The bracket I have is a stock one from an '89 c1500 with steering pump, alternator and ac compressor...
  11. J

    oil cooler thread size

    I have a 2006 Silverado 34" radiator (on an '89 c1500 with a 4l60e) and I'm installing a B&M auxiliary oil cooler. I"m looking for the thread size in the radiator. Almost everywhere I find it should be 3/8" but that's way too small. Measured with a vernier it is much closer to 5/8" or could it...
  12. J

    where used?

    Anyone got an idea where these are used in an '89 c1500? Too long ago and I can't remember where they were used for....
  13. J

    4l60e shift linkage

    I swapped my th700 for a 4l60e, don't know what year it is though. Can I still use the old shift linkage or do I need a cable? Apparently it is also missing the Neutral Safety Switch, is it only used to prevent starting when it is in gear?
  14. J

    Which connectors

    I'm building my own EFI but got a little stuck with the connectors I need. First one is for the O2 sensor, it is a Bosch LSU4 from FAST Next is from the throttle body, Edelbrock Pro Flo XT 3869 Both IAT and TPS And also the MAP sensor, Edelbrock 36019 I got some...
  15. J

    stand alone transmission controller

    I'm installing a 4l60e in my '89 (used to have a th700) and was wondering if someone else did this too and how you controlled the transmissions. Which stand alone controller did you use and do you like it or would you go for another solution if you would to do it again.
  16. J

    torque converter

    I'm swapping my th700 for a 4l60e but I would like to use the torque converter that I just bought for the th700. It is a high stall Pro Torque converter and since the 4l60e came without converter, I was wondering if it would fit, any idea?
  17. J

    hello

    I found this site via google in my quest for info about gauge clusters. I'm currently rebuilding an '89 from the group up but with a '96 interior, still figuring out the wiring though. I already found tons on info on this site! My truck is an '89 c1500 2wd that was lowered 2-4 about 12 years...

Latest posts

Members online

... and 25 more.
Total: 1,699 (members: 75, guests: 1,624)

Forum statistics

Threads
64,528
Messages
1,396,025
Members
51,920
Latest member
Oetam

Share this page

Top