Recent content by warbird

  1. W

    screw size question

    I have a 1994 gmc 2500 regular cab, I am freshening up the interior. at work right now so I cant check. does anyone know offhand what size (length/diameter) the screws that hold the sill plate down are? I'm wanting to order some stainless replacements
  2. W

    FSM

    ya but right now I just really need to figure out how this positive wire assembly is routed. PO took off the old one and its gone. so trying to install the new one I need a diagram and was hoping to find it online so I don't have to wait...plus short on cash at the moment, ill start looking on...
  3. W

    FSM

    anybody know if anybody has uploaded a copy of the FSM for a 1994 GMC 2500 ?
  4. W

    1999 HVAC questions

    I have a 1999 suburban c1500 that just wont get off of the defrost vents. the control panel switch assembly is 130 on rock auto and I want to make sure that is the issue before I go blowing money. is there a way to ohm out the switch to see if it is good? and what is the easiest way to access...
  5. W

    will C2500 van brakes and rear end work?

    looking on rock auto it looks like the same PN on the rotors between the van and the C2500LD trucks, so I am going to go with a big yes on them working. however the rear axle is still in question...and if it will work do I need to switch out the whole 3rd member or can I just use the axel shafts...
  6. W

    will C2500 van brakes and rear end work?

    at my local pick a part there is a 1999 C2500 panel van, six lug hubs, I have a 1999 C1500 suburban with the 5 lug hubs. I know the C2500 3/4 ton LD trucks front calipers and rotors as well as axle will work to allow me to swap to 6 lug wheels, just wondering if the van pieces would work as...
  7. W

    front accespory drive assembly help

    okay all, i need your help. i have a 94 GMC 2500 2wd. it has the TBI 5.7liter in it. the front accessory drive was removed including the bat ground cable. all the bolts were mixed up and now i am trying to put it back together i have gotten the alternator and P/S pump side figured out but the...
  8. W

    O2 on a TBI with LT headers

    i have a 94 GMC 2500 2wd with the 5.7 TBI i am putting LT headers on it (heddman i believe) i was wondering what everyone does with the O2 sensor? i am planning on running the 2 headers with 2.25 pipe back to just past the tranny then have them come together into a 3 inch collector then going...
  9. W

    couple questions regarding my 4l60E

    thankss all for the answers.... another question ..... looking at the servo housing area it looks like i may be gettign a small leak out of the servo.... i've never torn into a servo but i am wondering how hard it is to do? do i need any special tools (to do it right) and as long as i am looking...
  10. W

    couple questions regarding my 4l60E

    okay guys/gals. so here's the deal. its a 94 gmc 2500LD 5.7 with the 4L60E, i recently had things happen to where this will have to become my daily driver. has in the past only been a junk hauler. so i am dealing with some maintenance issues. changed the rear end fluid (it was nasty and low)...
  11. W

    NBS Front Brake Swap for OBS Trucks

    thanks ccreddell, so the NBS both 2wd and 4wd use the same front knuckle but on OBS the 2wd and 4wd use entirely different suspension pickup points and knuckles.... dang...... looks like i need to find some junkyard parts and figure out how to make this work......
  12. W

    The Stupid Interior Questions Thread

    how do people get the dash and other textured plastic tri, so smooth and painted? do they just sand down the texture? and what about the padded portions of the dash? how do they keep the paint from flaking off when the plastic flexes with heat?
  13. W

    NBS Front Brake Swap for OBS Trucks

    the OP used NBS knuckles on a OBS.... with what appears to be just reaming the BJ holes.... am i seeing that wrong? it doesnt look like he used alot of fabrication skills to make it work
  14. W

    NBS Front Brake Swap for OBS Trucks

    does anybody see reason why you could not just use the NBS 4wd front knuckle and brakes as shown but put them on a 2wd OBS? for instance i have a 94 GMC 2500 (7200GVW) already has 6 lug but why could i not just put the steering knuckle from a 4wd NBS on it? are the LCA and UCA different from...
  15. W

    new guy from wichita ks.

    hey everyone, names phil. married with 11 yr old and 6 yr old step daughters and a 13 month old little boy. currently have 1994 gmc W/T 2500 and the wifes 1999 suburban 2WD the 94 will be my daily once i get a few things done to it, i've owned it for about 5 years but it has just been a...
See more

Latest posts

Members online

Total: 977 (members: 10, guests: 967)

Forum statistics

Threads
64,621
Messages
1,397,603
Members
52,110
Latest member
nmcdaniel

Share this page

Top