Recent content by stenny

  1. S

    92 k1500 4x4 not working

    I know i probably should have quoted you but i was just stating its not needed there would be no gain
  2. S

    92 k1500 4x4 not working

    No need for solid axels nust need to change torsion bars
  3. S

    92 k1500 4x4 not working

    It was the switch now it works perfectly
  4. S

    92 k1500 4x4 not working

    What is a sas? A 4bt is same block minus 2 cylinders. You need to do a body lift of 2 inch. And you may need to change torsion bars to a k2500 or 3500 bars. Ypu need custom engine mounts. Adaptors etc depending on ehat tranny you use
  5. S

    92 k1500 4x4 not working

    I was thinking about it but autozone has lifetime warranty on the parts i am swapping. And i am going to be doing a cummins swap in the next couple months i have my cummins already and ibam rebuilding it right now so i will have a 4 cylinder cummins turbo diesel and i am swapoing to stick...
  6. S

    92 k1500 4x4 not working

    ok so i think its the sensor that on the transfer case that gives the actuator that is in the front diff the signal to engage. where is that on the transfer case? i know there are 2 sensors but i just don't want to take out the wrong one
  7. S

    92 k1500 4x4 not working

    i would rather fix it the right way then to mickey mouse it
  8. S

    92 k1500 4x4 not working

    i might just wire a switch its just 12v on one wire and ground on other
  9. S

    92 k1500 4x4 not working

    so i put it in 4wd and front diff doesn't lock so 4wd doesn't work. i changed actuator because i had one i bench tested, i bench tested old one and it works so it must be a electrical issue or 4wd electrical. i have a np241c i just am not very good with wiring i checked to see and there is no...
  10. S

    Tutorial: 3" Body Lift

    hey pics aren't working can you repost pics or repost this with the pics?
  11. S

    Where to buy? rubber inner fender splash gaurds for behind the front wheels 88-2000

    I am about to make mine outnof sheet metal forget the rubber ones trim some sheet metal and get plastic rivets and be good for a coupel years
  12. S

    what is going on here? am not sure if control arms are bent or what is going on here

    ok so today i did my front shock and the control arm touches the top of he square where bump stop is. i need to raise front up about 2 inches for plowing because my truck drops when i put plow on. so i snapped a few pics to see what you all think and pics were taken while car was jacked up. also...
  13. S

    92 k1500 brake lights not working need help wiring

    No it was a relay a cut wire and adjustment of the stoplight switch
  14. S

    92 k1500 brake lights not working need help wiring

    so i connected everything and brakes work i just needed to adjust brake switch after all that thanks
  15. S

    92 k1500 brake lights not working need help wiring

    the orange wire kept brake lights on because i think spring in brake switch is messed up because it doesn't shut off taillights i tried adjusting it for like 20 min and no matter what i did brake lights stayed on when you let off the brake pedal. maybe i am adjusting it wrong idk anyone have...
See more

Latest posts

Staff online

Members online

Total: 1,591 (members: 12, guests: 1,579)

Forum statistics

Threads
64,477
Messages
1,394,743
Members
51,755
Latest member
GriffisClnCo

Share this page

Top