Recent content by Lost06

  1. Lost06

    For once someone help mw put an end to my headlight issue

    it might be the turn signal assembly. I believe that that has something to do with the headlights not working correctly, or at all.
  2. Lost06

    Wiring Harness Question

    I used a guy in Arkansas and he made my harness so that I didn't have to have 2 computers. However, it cost about $500. I sent him the harness from my 96 and the harness and computer from the L33 i bought. He sent it back 1 harness that used the L33 computer and connected to the factory gauges...
  3. Lost06

    Tucking front wheels.

    Do you happen to know his screen name? Where I found this pic, no one knew him.
  4. Lost06

    Tucking front wheels.

    Thanks, I've got a few other pics of trucks that apprear to be daily drivers as they aren't quite as pretty as that one and one is at the drag strip doing a burn out in a water box. but they are on another computer that I can't get to right now. But even though, those wheels on the green...
  5. Lost06

    Tucking front wheels.

    btw... i found the pics of that truck on this here.
  6. Lost06

    Tucking front wheels.

    Ok. sorry for being so late with my reply. I have been busy with the family and these damn storms we have had. Here is a pic of one truck that claims to be static dropped with wheels tucked. The offset doesnt look too drastic. I plan to bag it one day when finances allow. But even then...
  7. Lost06

    Tucking front wheels.

    Before I start, I did search and didn't find anything relevant to my question. I have a 96 GMC RCSB that is lowered 5-9. My problem is that the wheels are hitting the fenders on big dips and turning after trimming the fender lip WITHOUT an alignment. If I go get the alignment it will push the...
  8. Lost06

    lsx swap headers

    i used the Schoenfeld. make sure that your engine is as far forward as it can go. mine are hitting on the passenger side firewall. I am NOT going to pull the engine so I'll use the trusty old 3lb sledge to make it fit. but they did bolt right up.
  9. Lost06

    bolt pattern.

    I was researching RPO codes on my truck and it says its a 5X4.75. I thought all full size trucks were 5X5. Did I miss something?
  10. Lost06

    wheel lean...

    I recently had the bed off to replace it with another one and while it was off it was noticable. I was hoping that the old bed was maybe deformed from an accident but even with the new bed on, it still has a lean to it. When I lowered it, I noticed that the drivers wheel tucked more than the...
  11. Lost06

    wheel lean...

    Sorry guys. I meant to say it was the back wheel. 2wd didn't have an axle section. And I figured off road guys would see this more often with the abuse they give their trucks.
  12. Lost06

    wheel lean...

    I have a 96 2wd 1/2 ton. When I look at it from the rear. It seems that the drivers side tire lean in toward the truck. Has anyone had a similar problem or have a suggested remedy?
  13. Lost06

    95 GMC SIERRA RCSB

    How's the swap going?
  14. Lost06

    low rpm

    Details are sketchy since I saw it last night. But it didn't sputter or anything. It just stopped around those rpms
  15. Lost06

    low rpm

    Hi. Before throwing stones, I did search but didn't find any info pertaining to my issue. And I need input before I buy this truck. I have a rebuit 4l60e from a 96 GMC Sierra sitting in my garage floor. I found a 97 Silverado thatneeds a transmission for $1000. Its a really clean truck and the...
See more

Latest posts

Members online

... and 19 more.
Total: 1,659 (members: 69, guests: 1,590)

Forum statistics

Threads
64,524
Messages
1,395,821
Members
51,908
Latest member
Kendziora

Share this page

Top