Recent content by itst9

  1. itst9

    How to - Install -AN oil cooler lines

    Finally completed this upgrade. What a PITA if you do not remove the oil filter adapter. I was in a hurry and only removed the stock lines. Little did I think that by the time a wrench was put on the fittings this left about 8° to turn the wrench to tighten everything. Lastly the drive line for...
  2. itst9

    Uneve Pad Wear from Driver side to Passenger Side.

    If a caliper was stuck would I feel the truck pull to one side when braking? In this case pull to the right since the passenger side pads were more worn. This truck has mostly been doing city driving so on a normal day speeds really don't get over 45mph. But even at that speed and the occasional...
  3. itst9

    Uneve Pad Wear from Driver side to Passenger Side.

    Thanks! I will add more silicone to the sliders or just get new pins. The pins don't seem to have any flat spots. From the photos above I should have taken different photos. The photo on the left compares both pads that were on the caliper piston side. Photo on the right shows both pads that...
  4. itst9

    Uneve Pad Wear from Driver side to Passenger Side.

    Finally changed brake pads and rotors on my truck today and as i am looking through service records it appears they have never been changed. I bought the truck with 85K and it now has 150K. The problem I noticed was the break pads on the passenger side were much more worn than the driver side...
  5. itst9

    Anybody have any thoughts on this issue?

    Reading through this thread I have the same problem. However i believe it seems to be just the brakes, maybe the hydro boost? Or something in line with vacuum. The issue started as a small squealing noise that was intermittent and now is constant. Thinking it was a pulley i removed the...
  6. itst9

    Stainless Brake Lines

    Thank you all for the teflon advice. Brake lines were successfully replaced this weekend. To my knowledge no brake work was ever completed by the PO. The rear hard line and drivers side front had some marred threads which slowed the replacement down but were corrected. I was however quite...
  7. itst9

    Installing a Remote Start, Alarm, or Keyless Entry?

    As an update the remote starter unit has given me no trouble so far. Granted the remote start feature is only used in the winter. The door locks are also finally connected the only issue I have had is loose wiring in my door panel where I spliced in the door locks. After slamming the door the...
  8. itst9

    Stainless Brake Lines

    Doing some reading I finally purchased stainless brake lines from summit, front and rear along with a bleeding kit. Brake problems have never been present but I wanted to ensure it stays that way. Brake fluid has always been clear until this year. The ABS has never worked so I might dig into...
  9. itst9

    HIDs interfering with radio

    I have noticed this as well. Im running HID's in my hi beams with the 4Hi mod. It only occurs while the HID's are warming up with my RF Ipod adapter, the radio is fine if your listening to just the radio. There is also a wiring harness for the HID's so they are wired separately. Kinda intrigues...
  10. itst9

    Blower Vent Trouble

    Okay, thanks for the responses. I have located the actuators and all seems to be in working order. Now for the condenser freezing up I have read a lot of possible causes. 1. condenser is plugged 2. Low pressure switch not working 3. Over charged and cutting off to high pressure. Over charge...
  11. itst9

    Blower Vent Trouble

    After reading the posts I am having a similar problem with the vents blowing just a little on all fan speeds but the problem only occurs when i have my ac on full cold after a couple hours of driving. Its as if the system freezes up since I had my ac recharged, It never use to have this problem...
  12. itst9

    4l60e corvette servo

    Thanks. I'm relieved that part was not needed. Upon further inspection 91Bluestreak is correct and that is a 3/8" compression fitting.
  13. itst9

    4l60e corvette servo

    Random part question. I was able to finally get my corvette servo installed yesterday. Everything went just like a text book example removing and replacing the parts. The only problem I ran into was when i went to reinstall everything back into the transmission. As I crawled under my truck I...
  14. itst9

    dual inlet air cleaner???

    I found some pics on the link below that are close to what i needed to see. I also ordered the salad bowl from Summit today, they had free shipping! http://www.fullsizechevy.com/forum/image-gallery/snapshots-videos/466585-pics-my-intake-project.html
  15. itst9

    dual inlet air cleaner???

    Blue95 Do you have any pictures under your hood? Im curious to see what that salad bowl looks like from a top view. Thanks. By the way I like the stance of your truck.
See more

Latest posts

Members online

... and 17 more.
Total: 1,699 (members: 67, guests: 1,632)

Forum statistics

Threads
64,500
Messages
1,395,317
Members
51,832
Latest member
Skotrodz

Share this page

Top