Recent content by bestof1999

  1. B

    Cummins swap Ideas need help

    Ok so im doing a cummins swap, my truck is a 1995 chevy 6.5l 5pseed manual and i need ideas/advice for a intercooler. What is the best way to go. I want to put a 12v in. Got most everything else figured out
  2. B

    HELP WINDOW WITH FLATBED

    I need help asap, we were cutting some stuff off the flatbed of my truck and broke the rear window by mistake.. there is barley any room because of the headache rack and i does the rack need to be cut off the replace the window? thanks
  3. B

    How to install the Prebled system 1995 Chevy diesel???

    OK guys so i cant figure this out.. My haynes book has nothing in it about changing such thing. I blew my master cylinder out and the metal line was so worn it snapped behind the slave. I bought the bled unit in hopes of making it easier, but i cant even find a spot in getting the system around...
  4. B

    Engine too old to Chip?

    in fact, i have only seen 1 350 go that long.. I have seen a neglected 6.2l get 350k.. Was a 82 and i think those had issues compared to the later versions
  5. B

    Engine too old to Chip?

    Justin, my mom does lawn care im sure she has an extra one around somewhere Skylark, Ive been around a few 6.5s, if you treat them right they seem to outlast the truck itself, or in my case, the master cylinder for the clutch :/ then rockauto sends me the wrong part. But anyways, i hope it last...
  6. B

    Engine too old to Chip?

    hey guys my 6.5l diesel just passed 240k, bought it awhile back and i was wondering if i could add a "chip" for some more power and the #9 thingy for more fuel coming in. I have some blowby (as much as my 6.2l diesel has with only 112k) i wanted to know if i could push it without blowing...
  7. B

    PTO install

    Does anyone have any info on Installing a PTO on the nv4500? like what i have to do, where i can get the unit? anything will help
  8. B

    Crank Sensor and no spark

    ok so this is going back a long was to when i dropped my suburbans 5.7l vortec back in after a lovely 3 spun bearing replacement that took up a good part of my summer, So my suburban was making this load grinding noise when i turned it over, but when it ran it did nothing. I was asked by a guy...
  9. B

    NEED HELP WONT START

    Figured it out awhile back. I messed up reading out of my book, I set it at the "6" and not the ”8" on the disturber
  10. B

    NEED HELP WONT START

    5.7l vortec 1999
  11. B

    NEED HELP WONT START

    so i am very close to getting my suburban running. It cranks but doesnt want to fire up even the smallest of a cough. useing a multi meter i get a 12 volt charge at the end of my plug wires. What could be wrong? its getting fuel
  12. B

    TBI engine in a vortec

    Is it possible. Can i drop a tbi 350 into my 1999 suburban??
  13. B

    New Engine ZZ4

    So i have a chance to buy a ZZ4 coming out from a boat. Will this match up to my stock 5.7l Vortec?
  14. B

    Ring grove size

    can anyone tell my what my ring groove size is on a stock chevy 350 vortec 2 bolt main from a 1999 chevy k1500 4wd
  15. B

    New engine

    I am looking to get a used engine for my 1999 suburban that has a bad block thanks to a spun main bearing. Can i put a TBI motor with vortec heads in? will it match up?
See more

Latest posts

Staff online

Members online

... and 8 more.
Total: 1,784 (members: 58, guests: 1,726)

Forum statistics

Threads
64,472
Messages
1,394,657
Members
51,751
Latest member
brushwolf

Share this page

Top