64’ IHCC daily commuter tractor

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Orpedcrow

I don’t know what I’m doing
Supporting Member
Joined
Aug 20, 2022
Messages
2,612
Reaction score
6,665
Location
East Texas
You must be registered for see images attach

Check out this funky pto. It’s all seized but still neat.

You must be registered for see images attach

You must be registered for see images attach

I wish pulling engines out of gmt400 s was this easy lol

You must be registered for see images attach
You must be registered for see images attach

Old clutch and drive hub. Those are spiral roll pins (they’re everywhere)
 

Orpedcrow

I don’t know what I’m doing
Supporting Member
Joined
Aug 20, 2022
Messages
2,612
Reaction score
6,665
Location
East Texas
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach

Billet hub and pressure plates. Heavy duty spring for more holding power. Longer lever arm to overcome the heavier spring.
 

Orpedcrow

I don’t know what I’m doing
Supporting Member
Joined
Aug 20, 2022
Messages
2,612
Reaction score
6,665
Location
East Texas
Installed, just need to adjust the guide pins and lock them down. Had to modify the lever arm bracket for the new heavy duty arm. Eventually I’ll add a strengthening support to the section that the mount is bolted too (it flexes when the pedal is pushed)
You must be registered for see images attach
You must be registered for see images attach

Springer seat ready for install. Don’t k ow if I’ll leave the seat the colors it is or strip and paint it.

You must be registered for see images attach

And here it sits till tomorrow. So far no reason I can’t drive it then.
 

Orpedcrow

I don’t know what I’m doing
Supporting Member
Joined
Aug 20, 2022
Messages
2,612
Reaction score
6,665
Location
East Texas
You must be registered for see images attach
You must be registered for see images attach

So close to driving it.

Busted off a valve stem and the tire is FULL of water, so I spent about 2 hours changing the tube today.

Chinese carb had the float stuck open so I took it apart and cleaned it.

This thing sounds so cool when it cranks, little single cylinder, low compression with a starter generator.

Now I’m off to research brake adjustment ( internal to the transmission) I can’t change gears with it running because it won’t stop driveshaft.

I MIGHT… start a YouTube channel so I can post videos.
 

Tommy1234

I'm Awesome
Joined
Mar 22, 2022
Messages
2,047
Reaction score
3,113
Location
Chicago il
You must be registered for see images attach
You must be registered for see images attach

So close to driving it.

Busted off a valve stem and the tire is FULL of water, so I spent about 2 hours changing the tube today.

Chinese carb had the float stuck open so I took it apart and cleaned it.

This thing sounds so cool when it cranks, little single cylinder, low compression with a starter generator.

Now I’m off to research brake adjustment ( internal to the transmission) I can’t change gears with it running because it won’t stop driveshaft.

I MIGHT… start a YouTube channel so I can post videos.
Do it buddy
 

Orpedcrow

I don’t know what I’m doing
Supporting Member
Joined
Aug 20, 2022
Messages
2,612
Reaction score
6,665
Location
East Texas
You must be registered for see images attach

You must be registered for see images attach

xc_hide_links_from_guests_guests_error_hide_media

Finally got this sucker goin’
I’m a happy man.

Steering is CLAPPED!! :hump:
 
Last edited:
Top