-
-
Got a chance to deglaze the cylinders today. When I bought the hone, I grabbed a package of fine hones to change out the medium ones... -
EJ_74 reacted to KY-N's post in the thread Advantage West Corp. Dealership Upgrade 1994 GMC Sierra Z71 with
Like.
I don't know about the "Advantage" truck but the running board and fender flare look identical to those on my 92' K3500 -
EJ_74 reacted to HotWheelsBurban's post in the thread Advantage West Corp. Dealership Upgrade 1994 GMC Sierra Z71 with Like.
Cool truck!
-
EJ_74 reacted to Fryall4's post in the thread Advantage West Corp. Dealership Upgrade 1994 GMC Sierra Z71 with Like.
Hello all, I just picked up this 94 Z71. I remember seeing these Advantage trucks back in the day and was wondering if anyone had any...
-
EJ_74 replied to the thread Early metric fasteners identification.Cool! How durable is that coating?
-
This may be before you were born, but when metric fasteners first started becoming available they were a red copper bronze color. This...
-
EJ_74 replied to the thread Supercharger any one every seen this.That sounds interesting. Can you get any better pictures?
-
@name - toppers are a dime a dozen on FB. I don’t see them too often on Craigslist anymore really. Tonneau covers are harder to find...
-
EJ_74 reacted to NickTransmissions's post in the thread 4l60 rebuild shifting issues after 1k miles with Like.
Check the speed sensor in the transfer csse - it may be weak and not producing enough voltage once above 25-30mph or so (does your...
-
I discovered this the hard way. When I made the roof rack for my truck I took careful measurements at the back of the truck and made...
-
EJ_74 reacted to Sean Buick 76's post in the thread Changing tie rods without jacking up truck? with Like.
Time to save up for your own place lol! I don’t remember asking for permission but I would pull my truck into my parents garage and tear...
-
You are correct. Bracket to bellhousing then stud/bolt. That spot at least on my truck was a bolt. Two studs further down for the heat...
-
Looks like the same GM part number you have listed on your etsy page covers the 95 TBI 454 as well. Gaskets look good in the photos.
-
EJ_74 reacted to Cadillacmak's post in the thread 96-99 CPI Truck throttle body INLET gasket with Like.
I will try them out when they get here, if they fit the carbs I will leave a review with pictures, because I have never found a good...
-
EJ_74 reacted to el torro's post in the thread 96-99 CPI Truck throttle body INLET gasket with Like.
From what I can find online the Fel-Pro gasket I used as a model for this is the same across carburated vehicles for a lot of...
-
-
Loading…
-
Loading…
Staff online
-
df2x44L60E Destroyer
Members online
- bjohnm
- RichLo
- Alteca
- Brwnelky
- dippin-dave-420
- 93Xtra-Cab
- Hondamike541
- Drunkcanuk
- caw_86
- zodiac572
- 1990Z71Swede
- BNielsen
- jerry67
- termite
- BadCompany750
- 91hurcules4x4
- Gravyyy
- Planb_smoothie
- Harry S Morgan
- Charlesteneows
- Orpedcrow
- dave s
- Stagern
- Astro
- Spareparts
- Oldude
- jess t
- ctbhess
- D_EATON
- Cadmaro
- User_name
- Mindtriped
- Obsbeast
- df2x4
- cuccia69
- 95YardArt