Search results

  1. F

    Brake lines + Prop valve questions

    Ok, first off not near my truck and want to pickup some brake line. Anyone able tell me what size the line is for the back and front? So when doing my SAS i'm going to ditch the ABS module so I have to build a new system. From the master I need a proportioning valve to reduce rear...
  2. F

    Slip Yoke Eliminator for a 243?

    I have found JB Conversions who offer a SYE for the 243. Can keep the stock speedo housing and then choose either a 1310 CV yoke, 1350 Non CV yoke or the 1350 Rear Output Flange. Just wondering if anyone has bought one of their kits or can you recommend someone else who sells one? When I...
  3. F

    Pic request, Bracket removal for SAS.

    Finally getting back to working on my 98. Seems there's always other crap getting in the way of my fun. Anyways, i'm wondering what people are doing in regards to the front cross member where the lower control arms originally mounted to. Just leave the whole thing or trim it to get rid of...
  4. F

    SAS question. ABS module

    Quick question. When people do their axle swap do you leave that abs module hooked up with the lines running through it or do you bypass it allowing removal? Imagine either would work but wondering what people have done Thx Sent from my BlackBerry 9800 using Tapatalk
  5. F

    Putting the pride back in my pride and joy

    Well my 98 had been put out to pasture so to say a little while ago while I wasted time and money on a 05 jeep rubicon. It wasn't bad but never truly made me happy as my full size chevy did. So got rid of the jeep and finally ready to bring back my pride and joy!! Alot of my frustration with...
  6. F

    Amount of lift for 40" tires on SAS??

    Well i'm finally starting to do some work on the 98. Originally I was going to run a 38" tire however my buddy is upgrading to 40s on his jeep so i'm unsure which size I will go. I plan to play on rocks as i'm finally over mud and how it helps rot my truck. So the brackets usually add...
  7. F

    Head Gasket Time

    Well today the head gasket on the passenger side let go. Over the years she had overheated a time or two so when apart going to make sure to get the heads checked. Anyways onto the parts needed. While looking online I noticed depending on any shaving you can get different thicknesses...
  8. F

    LMC truck body parts. Anyone buy from them??

    So my truck needs some TLC. Big thanks for salt on the roads up here over the years and wheeling. Anyways I need some cab corners and fenders. Anyone buy from LMC, how are the quality of their fenders?? Don't want to change em again in 2 years if possible. Thanks for input!!!
  9. F

    14 bolt FF park brake options?

    So other than elderado calipers for the rear what are people doing for a park brake when converting to disks? Yota guys can buy a disk and caliper setup for the transfercase, anyone make that for chevys? Local law enforcement has a habbit of harassing people with modified vehicles around...
  10. F

    4L60E issue..

    So following the sticky here is my issue. 5. Trans shifts into gear harshly, 3rd gear starts, manual 2nd available but no 1st, no 4th, and no TCC lockup: No power to transmission, or trans is in limp-home mode. Check wiring, and make sure transmission electrical connector is plugged in. Easy...
  11. F

    Where is good place to buy parts?

    Need to start getting parts for my SAS. Have a 90 Dana 60 and will be ordering gears, master install and locker, for the back is a 14 bolt so same deal. Fair amount of places out there but i'm wondering where people have had good experiences? Thx
  12. F

    Cab corners and front fenders? where to buy

    Winter has been very hard on the ol 98. Stupid salt because people can't drive. Anyways i need cab corners and atleast a front right fender. I was wondering if anyone knows who has these parts? I was on LMC trucks website and found them. Figured i'd ask where people buy their parts...
  13. F

    DC Sage 2, which steer stabalizer?

    I'm going to get a steering stabalizer for my 98. I'm just wondering if a standard aftermarket stabalizer will work for my lift? Thanks!!
  14. F

    4L60E build?

    I figure it's better suited here as in the street section not many might check that. Need off-roaders input. :) So, trans has drank water a number of times now, once i had to drive about 100 miles with water and it was making some bad noise. Flushed it a couple times and it has held...
  15. F

    Woo, no more 5.5" block.

    Well today I finally got around to installing my shackle flip. Bought the off road design kit. Since i'm thinking SAS i didn't want to get rear springs yet so for now a 2" block is in there. Couple pics my buddy took, poor truck could really use a frame cleaning and some paint...
  16. F

    Shackle Flip Question

    Finally going to do a flip on my 98. The bolts for the shackle goes from the frame side to the outside. So how are you removing the bolt with it hitting the frame? I haven't tried yet, just looking to prepare for the job!! Also, anyone made their own u bolt flip plates? Like the...
  17. F

    So, would you use a 36.5 ford dana 60??

    Have found a dana 60 from a 90 f-350. Have been told they are less desireable due to width. I'd be running max of 38's. For my 98 rc/lb. Thx
  18. F

    Ontario Canada members

    I'm up in sudbury.
  19. F

    Anyone tuning their truck with efi live??

    I got efi live for my d-max and since there is a second license tossed a tune into my 98 350. Wondering if anyone is familiar with efi live and gas tunes? Thought maybe could take a look at my tune. Thx

Latest posts

Members online

Total: 1,534 (members: 30, guests: 1,504)

Forum statistics

Threads
64,476
Messages
1,394,729
Members
51,754
Latest member
Riccoon

Share this page

Top