Search results

  1. willdabeast69

    OBS (Old Blown up ) to NBS (New Bad ass ) Build Thread

    205 reassembled with the new input shaft you can tell the size difference in the 32 spline vs the 10 spline.
  2. willdabeast69

    Hydaulic Ram Assist Steering build thread

    nice! thanks for the input buddy. Im assuming you tapped the top cover as well?
  3. willdabeast69

    Hydaulic Ram Assist Steering build thread

    you got a picture of it?
  4. willdabeast69

    Hydaulic Ram Assist Steering build thread

    digging up dirt... but where did you get the end plug from? i can't find one anywhere..
  5. willdabeast69

    OBS (Old Blown up ) to NBS (New Bad ass ) Build Thread

    Yeah i checked for leaks with soapy water, and yes i did get the anti-cone rings
  6. willdabeast69

    OBS (Old Blown up ) to NBS (New Bad ass ) Build Thread

    Thanks dude! I got the kit from http://www.diybeadlocks.com/ and just used an old set of steel wheels i had laying around, welded them up and bolted them down pretty straight forward but i tell you what doing 4 of those wheels gets tiring lol
  7. willdabeast69

    OBS (Old Blown up ) to NBS (New Bad ass ) Build Thread

    got the doubler in just waiting to get the 205 back from the machine shop.
  8. willdabeast69

    OBS (Old Blown up ) to NBS (New Bad ass ) Build Thread

    but i made the decision to go under the knife again and do a doubler (203/205) to add some length to the front driveshaft. it would just be too short and the angle would just not work with the amount of lift. also decided to ditch the bed and flat bed it. also made a new set of beadlocks and got...
  9. willdabeast69

    OBS (Old Blown up ) to NBS (New Bad ass ) Build Thread

    well its been way too long since an update has been made but got it running and driving with the 4 speed
  10. willdabeast69

    power window conversion parts list question ( mod please move)

    if you werent in ky id trade you my power windows for your manual ones
  11. willdabeast69

    OBS (Old Blown up ) to NBS (New Bad ass ) Build Thread

    oh yeah it is. oober weighted shift knob
  12. willdabeast69

    OBS (Old Blown up ) to NBS (New Bad ass ) Build Thread

    I love the 4 speed especially the granny low gear
  13. willdabeast69

    OBS (Old Blown up ) to NBS (New Bad ass ) Build Thread

    well i got an update for ya'll! been a while since ive posted anything on here but lets just say ive made a few changes :naughty: so i got fed up dealing with auto transmissions and picked up a sm465 and np205 for cheap! obviously pretty gross so i had to clean it up a bit and inspect the...
  14. willdabeast69

    sm465 swap

    also from what i've been reading the input shaft is the same size and same spline count as an nv4500 so i think this will be a relatively bolt in swap
  15. willdabeast69

    sm465 swap

    Yeah I want to run my pdrop 241 behind the 465 to get a super low, low range to make crawling way easier Sent from my SCH-I545 using Tapatalk
  16. willdabeast69

    sm465 swap

    Ok thats what I was thinking. Thanks boss. And any tcase with the 6 bolt pattern and 32 spline input will work Sent from my SCH-I545 using Tapatalk EDIT: but the 32 spline 6 bolt tail housing was the later sm465's i think like 1975-1991. before then it was the 10 spline output for the 4wd and...
  17. willdabeast69

    sm465 swap

    But anyways back to the original topic.. Other than pedals and a master cylinder out of our trucks. Can I use the clutch and fly wheel that would go behind our motors? Or would I have to get one for the older cdi motors?
  18. willdabeast69

    sm465 swap

    i turned 38s with 3.73s with my old 4l60e lol im fine i got plenty of power
  19. willdabeast69

    sm465 swap

    yeah 4.10s and 37s ill be more than fine till i get 39.5's
  20. willdabeast69

    sm465 swap

    why? because they suck lol real problem now is in the valve body i have the po1870 code so i was just gonna buy the transgo shift kit to fix the problem
  21. willdabeast69

    sm465 swap

    yeah im on my second one from monster transmissions. im gonna fix the problem then try to sell it
  22. willdabeast69

    OBS (Old Blown up ) to NBS (New Bad ass ) Build Thread

    like diss? ;)
  23. willdabeast69

    sm465 swap

    dont need OD and my brand new trans is having issues...again. and nv4500's cost more than i bought my truck for up here lol
  24. willdabeast69

    sm465 swap

    has anyone swapped a sm465 behind a vortec on here? looking to swap out my monster trans for a 4 speed
  25. willdabeast69

    OBS (Old Blown up ) to NBS (New Bad ass ) Build Thread

    with all the problems i ran in to it wouldnt have happend lol

Latest posts

Members online

Total: 1,263 (members: 26, guests: 1,237)

Forum statistics

Threads
64,464
Messages
1,394,640
Members
51,726
Latest member
ThatOldRedFarmtruck

Share this page

Top