Search results

  1. M

    Gooseneck Pictures

    Nice truck. I just got a set of airbags for mine. I tried putting them in but couldn't since I lifted it. Waiting for my spacers for the kit now.
  2. M

    1999 CCSB drive line vibration after lift

    Well it's been at the drive line shop for almost 3 months. They say there always to busy to mess with it. I guess they tried a few things but it was worse than when it came in. They tell me it's perfectly fine to drive. And that they will let me know when they will have time to look at it...
  3. M

    1999 CCSB drive line vibration after lift

    Well I happen to have a friend who owns a drivline shop locally....I ended up dropping it off there....I'll see what he comes up with....
  4. M

    Horrible grinding noise - Can't seem to figure out

    I assume the new compressor came with a new ac clutch?
  5. M

    1999 CCSB drive line vibration after lift

    I put a RCD 6 inch lift in my truck and I have a slight vibration on takeoff. I also feel a vibration in my feet through the floors while doing highway speeds. I just had the drive shaft rebuilt with new u joints and a new carrier bearing. Also had it balanced. The shop told me it was a...
  6. M

    98 chevy 3500 crew cab 4x4 engine advice

    I dont know about your area but the local pick and pulls charge 200 for a engine with accessories....Call aroud junk yards and see what they have....
  7. M

    Gooseneck Pictures

    Who here uses a gooseneck and what kind? Lets see some pictures?
  8. M

    What have you towed lately

    Those axles seem really far back.
  9. M

    1999 Vortec 7400 injector swap

    i was going to get a tune from Black Bear Performance. I will tell him my problem. Hopfully he can get it to work. I really dont feel like changing them again lol
  10. M

    1999 Vortec 7400 injector swap

    i upgraded the injectors on my 1999 GMC 7.4 from the factory one to the ls1 injectors. Truck runs good now. but I now have a SES light on. I have a p0172-p0175. Both rich codes. I assume its because I have bigged injectors. I was under the impression from all that I read here that it...
  11. M

    1999 Vortec 454 Rough idle

    Going to pull it apart tonight to check. Along with du checking my other work. Maybe I missed something.
  12. M

    1999 Vortec 454 Rough idle

    I wish I checked the dam distributor when I had everything apart. I keep reading the gears are know to go bad.
  13. M

    1999 Vortec 454 Rough idle

    Also it had the factory injectors in it. I was told they were changed by the previous owner but they were pretty rusty so I have my doubts. I also changed the O2 sensor on bank one. I had a lean code bank 1 sensor1. I put the O2 in and did the tune up along with the injections and the FPR...
  14. M

    1999 Vortec 454 Rough idle

    My truck has 92,000 miles. And sorry its not my Tahoe. Its my 1999 K2500 CCSB. Its starts right up most times. Had a couple hard starts with some backfires out the exhaust. Today took it for the first drive in about 2 months. Now it spits and sputters under load. Pops and backfires as...
  15. M

    1999 Vortec 454 Rough idle

    Having a hell of a time figuring this out. My truck has had this rough idle since I bought it. It idles rough and stumbles until it gets about 1500-2000 rpm. No engine codes are stored. It did have a hard time starting and backfired a little a few times but it hasnt done that again. It...
  16. M

    Re installing Torsion Bars

    OK guys....So I am installing a 6 inch RCD lift kit on my 1999 K2500.....Had some issues with the driver side spindle not fitting and RCD had to get me a new one.... The problem I have is the truck has been sitting on Jack stands in my drivway for 6 weeks while I was jerking around with the...
  17. M

    RCD Lift Kits

    Anyone have a RCD lift kit in there trucks? Specifically a 88-2000 2500 or 3500? Looking to pick your brain.
  18. M

    1999 Vortec 454 Running rough and drivning me nuts

    Got rid of the p0135 with a new O2 sensor. Truck has same issue. Now I have a P0171 Code. I have checked the O2 on a scan tool. I added fuel(carb cleaner) to the engine and the STFT changes on both banks when I spray. It goes from about 0%-3% to about -15% when I spray carb cleaner in...
  19. M

    1999 Vortec 454 Running rough and drivning me nuts

    The truck stalls when I unplug the MAF. Also have a P0135 cide now.
  20. M

    1999 Vortec 454 Running rough and drivning me nuts

    Is that where the ground is? Ill check.
  21. M

    1999 Vortec 454 Running rough and drivning me nuts

    Also it has had a new fuel pump and filter in it. But the needle bounces on the gas guage now.
  22. M

    1999 Vortec 454 Running rough and drivning me nuts

    I got my hands on a scanner. Have 3 codes. P1122,p0122,p0102.
  23. M

    1999 Vortec 454 Running rough and drivning me nuts

    No Ideas?
  24. M

    1999 Vortec 454 Running rough and drivning me nuts

    It idles at like 550 and the truck shakes. Misses and stumble when you give it gas
  25. M

    1999 Vortec 454 Running rough and drivning me nuts

    My 1999 GMC ccsb is running pretty rough. I have already done plugs, wire, cap, and rotor. I have also done the FPR. The previous owner said the injectors were done but im not entirely sure they were. They looked a bit rusty when I had the intake of to do the regulator. He also told me he...

Latest posts

Members online

Total: 1,513 (members: 40, guests: 1,473)

Forum statistics

Threads
64,394
Messages
1,393,065
Members
51,570
Latest member
Jefferson Annabel

Share this page

Top