Search results

  1. 94Chevyshorty

    ummm..is this my transmission leaking?

    My guess is it could be your rear main seal leaking from where the motor and trans marry, theres usually a vent hole at the bottom of the flywheel casing and sometimes rear main seal oil leaks out of it. as for the transmission pan, i would say it could be the pan gasket or it could be leaking...
  2. 94Chevyshorty

    Crew cab rear seats

    If your looking for that setup, most dodge rams with the backseat like the 98 ram area.. you can fabricate the mounts and put a dodge seat in there, they have the little cubie underneath the seat, buddy of mine keeps his rifles under there.
  3. 94Chevyshorty

    94 Chevy Truck Tailight issues

    From what i know the ground on these trucks is on the drivers side near the 4 prong connector and mine seems to be right underneath the crossbeam.
  4. 94Chevyshorty

    Tail light issues after removing bed

    Yes i have that ground it bolts to the frame right under neath the back frame crossbeam. its a white wire, how would i wire another ground to the whole circuit?
  5. 94Chevyshorty

    94 Chevy Truck Tailight issues

    1994 chevy silverado shorty, took the bed off recently and now i'm having issues with the wiring, the 4 prong connector that comes from the front of the truck is perfectly fine. turn signals, markers, and reverse lights show up from that plug at full power, but then i connect it to the bed...
  6. 94Chevyshorty

    Tail light issues after removing bed

    Im guessing its gotta be ground because all my fuses are good and everything has been updated with fresh fuses recently.. my 3rd brake light lights up nice and bright, but its just the tail lights. also, when i turn my parking lights on, the backs aren't on, but then i turn them off and put the...
  7. 94Chevyshorty

    Tail light issues after removing bed

    Ive got a 1994 chevy silverado, i had to do some frame work and a fuel pump underneath the bed, the lights had no issues before the bed came off, the taillights are very dim, directionals very dim and fast, no parking lights in the back. only in the back though, the front lights and roof markers...
  8. 94Chevyshorty

    Tips on welding in new rockers and cab corners??

    Bed is off, i put the lift feet under the front panels towards the headboard, then put extentions and 2x4s all the way up to the back of the bed floor. lifted er' right up! frame looks okay... Found a new spare tire carrier off another truck, (better shape than mine) and i have to weld a little...
  9. 94Chevyshorty

    Tips on welding in new rockers and cab corners??

    Tires would have to come off as well as the back bumper. which is probably rusted on for life haha
  10. 94Chevyshorty

    Torsion key lift question

    I did it with my 94 silverado to fit my 33s under it with no rub. you will be fine
  11. 94Chevyshorty

    My 94 Chevy RCSB, 350 tbi (Project truck)

    Well the truck has a 350 Tbi strong running, 4l60e overdrive, 4 wheel drive with perfect running transfer case. Also has the 3.73 gearing in the back with the G80 locker (i love it). Recently i just finished swapping the flywheel, i had to put a new flywheel in from chipped teeth. And now im...
  12. 94Chevyshorty

    Tips on welding in new rockers and cab corners??

    Did you just hook it to the bed rail pockets and lift? it didnt bend the bed rails at all?
  13. 94Chevyshorty

    Tips on welding in new rockers and cab corners??

    That might work, but the only issue is my bed is pretty rotted out. think it will hold?
  14. 94Chevyshorty

    My 94 Chevy RCSB, 350 tbi (Project truck)

  15. 94Chevyshorty

    stumble on accel.... tbi350

    I had the same issue with my rcsb chevy too. it turned out to be a bad 02 sensor.
  16. 94Chevyshorty

    Wheel size preference

    I run the stock 16s. 33s fit underneath the truck with those rims perfect.
  17. 94Chevyshorty

    Bad motor or ?????

    It only does this when its under a load? Could be a bad lifter, any engine mods???? I would say check your 02 sensors, i had alot of misfiring and limp mode all day with a bad 02. they usually like to rust so bad theyll fall out of the pipe. But if youve got a knock under a load and it gets...
  18. 94Chevyshorty

    4l60E Loud tick when going into park normal?

    I get a loud clicking sound, not quite a knock, but just a loud click, Normal? I always let the truck settle in neutral before locking the transmission into park. so theres rarely any stress on the transmission while in park. Normal or should it be a concern?
  19. 94Chevyshorty

    Tips on welding in new rockers and cab corners??

    Thats a good idea. because my under side of my bed is rusted, but my external fenders and bed rails are great. How did you strap it to the bed?
  20. 94Chevyshorty

    Tips on welding in new rockers and cab corners??

    How could i scoot my bed back with a lift? the underneath of my bed is pretty rotted out.
  21. 94Chevyshorty

    3.73 ratio with a G80 locker?

    I dont beat the truck, the differential is fine at the moment, it just caught my eye that it did not want to lock both tires when i was in snow once, but the i tried again and it did.. locker getting tired?
  22. 94Chevyshorty

    4l80e problems

    Id look into a new Torque converter. i have the 350 with the 4l60e and they start to go at high miles. How many miles you running? Transmission ever been separated? Bad trans fluid? Cheap Fluid? Go to the chevy store and pick up some Dexron VI. Its rated for newer Gm rigs with the 6 speeds, but...
  23. 94Chevyshorty

    3.73 ratio with a G80 locker?

    Ive got 3.73 gears with a g80 in the back.. getting old, any common issues with them? ive been seeing alot of them needed a rebuild. im running high miles
  24. 94Chevyshorty

    Tips on welding in new rockers and cab corners??

    pretty sure i have to pull the finders off too. at least loosen them if anything, but i was told that it possible to cut the rocker in half and do the easier part towards the back first... no door removal required
  25. 94Chevyshorty

    Headers or Stock manifolds/Y pipe?

    I found some that might work, im liking the long tubes. i wonder if the long tubes would clear the frame.

Latest posts

Members online

... and 25 more.
Total: 1,761 (members: 75, guests: 1,686)

Forum statistics

Threads
64,455
Messages
1,394,438
Members
51,711
Latest member
TTdog

Share this page

Top