Recent content by SilvyLightning

  1. S

    Bodylift and some

    From the mounting holes to the tip where he ball joint is there is a good bit of angle. Approx 2" drop towards ball joint My cv axles also have a little drop to them
  2. S

    Bodylift and some

    Sorry I seen my post and I must of looked at a kit for a different truck. From my side view and a measuring tape my truck sits level so the keys must of been turnt up at least 1" to 1.5" I don't really want to crank them to much so what would you say would be to much on cranking them. Is it...
  3. S

    Bodylift and some

    Ok that's sounds good. I may be ordered just the rear 3" and for the front Maybe 1.5 spring spacer with my keys cranked. Also my key say "keyway-03" on them are they factory
  4. S

    Bodylift and some

    I have a 3" bodylift. First off is it even safe and doable to throw a 3" rear block kit and 3" key set like this on top of a body lift...
  5. S

    Long tubes

    I have found two. Depends if you have the offset engine simply found by measuring the crank pulley bolt to the left and right to determine if it's a engine offset to the passenger side Check the footnotes on both of these pages My truck originally had a offset 5.7 in it I replaced it with a...
  6. S

    WHAT headers

    Also SSA says these fit too https://www.streetsideauto.com/p/hedman-painted-hedders-69440/?utm_source=googlepepla&utm_medium=adword&gclid=CjwKCAjw6szOBRAFEiwAwzixBT_EEv4NqRux1A8Hfabbn3bbRbraQLF5Nd27w5vamkwtUQWBfwoW5BoCwfUQAvD_BwE Also hedman 69440 is under 200 and fits our trucks. There...
  7. S

    WHAT headers

    Ok I'll research them. I didn't want to spend more than 200$ on a set and I found some at Autozone that say they fit http://m.autozone.com/exhaust/exhaust-header/flowtech-exhaust-header/398693_305776_0?location=
  8. S

    WHAT headers

    Okay. That makes sense about trial and error I've looked over jegs summit and eBay. I can't find any longtubes for a 90. All I've found is shorties or mid length. I know someone out there actually makes them
  9. S

    WHAT headers

    I just put my build back together it's a 84 4 bolt 350 with vette tbi heads and intake off a 86 or 87 can't remember exact year But what headers fit out gmt400s I got a set of 68 Camaro long tubes and a set of headers off a 72 c10 Does any sbc headers fit seeing how we have so much engine bay...
  10. S

    what tire size under 3" body lift

    I got a 90 k1500 3" body lift stock "4x4" wheels with 315s. I may add a 3" suspension lift so I can throw some wider wheels and space them out in the future but for now 315s fill up the fender nice. Go 33"s if u do a lot of flexing.
  11. S

    Ac swap troubles.

    Do you know the port configuration? I assume Autozone may have my sealing washers, they had replacement ones for my year, make and model. As far as I can tell. The accumulator, lines and condensing radiator is all factory.
  12. S

    Ac swap troubles.

    This isn't the photo I got of it. Any insight? I don't see why I couldn't go to a pick n pull. Snip the little harness connector I need for it and grab a accumulator and lineset for the compressor
  13. S

    Ac swap troubles.

    Okay I'll post pictures tomorrow. When I attempt to bolt on the ac lines using the washers that's there it seems to me like the right one(yellow plastic on it) is to thick or large for the hole. It sits a little crooked so I'm sure it would leak. But I'll snap a few photos in the morning
  14. S

    Ac swap troubles.

    Just swapped the 305 tbi outta my 90 for a 87 vette motor. Well the vette motor has a 93 silverados ac compressor. I had to go to a pick and pull and snip off the harness connector for it as my 1990 connector was different However the issue I'm having is with the ac lines bolting up with...
  15. S

    90 k1500 starting issues

    i had a buddy of mine lose my truck keys and he drilled my column. Well to no avail we didn't get it started and I ended up having to replace the tilt column because we drilled into some rod that turns a gear/pushes rod into the switch. Well long story I bought a used 1988 tilt, cruise column...
See more

Latest posts

Members online

... and 17 more.
Total: 1,952 (members: 67, guests: 1,885)

Forum statistics

Threads
64,674
Messages
1,398,551
Members
52,211
Latest member
HenryFordWasRight

Share this page

Top