Recent content by Nick Wheeler

  1. N

    camaro temp sender

    i wonder if that would use the correct resistance to work with a 0411 pcm?
  2. N

    camaro temp sender

    i havent gotten around to working in this again yet, but ill probably end up putting the correct sender for the gauge in the passenger head
  3. N

    camaro temp sender

    thanks! does your gauge read correctly though? thats the topic of the discussion
  4. N

    camaro temp sender

    thats what i figured too. think the other guy was suggesting using 2 of them, of for the pcm and one for the gauge, since the sensor is compatible with either
  5. N

    camaro temp sender

    thanks! ive still got a few bugs to work out and clean up to do (mostly wiring) so, using the vortec sensor the output would go to the pcm and "t" to the gauge since its only a 2 wire? wouldnt the reading be skewed by the resistance from the guage? ive already got a temp new sender for the 95...
  6. N

    camaro temp sender

    anyone else use the 3 wire camaro temp sender on their swap? i decided to go this route and my stock temp gauge reads about 30-40 degrees off (cooler) than my scan tool... any idea what needs to be done other than running a sender from the tbi motor in the other head to run the gauge? dont...
  7. N

    C100 connector disassembly?

    wasnt sure where to put this, but im nearing the end of my ls swap on my 95 k2500. when i was sorting through the tbi harness i nipped some wires off the c100 (drivers side bulkhead) connector that i didnt think id need (vehicle speed signal, tach, the big pink ignition feed, tcc switch and a...
  8. N

    wheels 95 K2500

    thanks! i cant speak for just the ujoint itself since i rebuilt the entire front end at the same time, but the rag joint was extremely worn out (along with everything else) my truck feels like a totally different one now, and i'd be willing to bet on a truck with a good front end and a sloppy...
  9. N

    wheels 95 K2500

    thanks! i doubt it. you have to cut the end off the shaft
  10. N

    wheels 95 K2500

    continued, again... and pulled the bed to replace the fuel pump with a vortec pump ep381. while the bed was off i also added 1.5" lift blocks to the rear and finally, heres how she sits now! thanks for putting up with the long intro, ill keep the rest of the posts shorter lol
  11. N

    wheels 95 K2500

    continued... burning out old control arm bushings pressing in new joints, i ended up taking the arms to work and using hydraulic the press old rivets out of the uppers mostly back together while i had everything apart, i also took the time to cut off the old worn...
  12. N

    wheels 95 K2500

    since ive been lurking around here for a while, figured id start a build thread to share my trucks progress (or lack of) this first post might end up pretty long winded, as i've done quite a bit of work since i got the truck. Its a 95 K2500 eclb, tbi 5.7, 4l80e, np241, 9.25 front, 14bsf rear...
  13. N

    New "born again chevy guy" from AZ

    Thank you! I wish i could say the shop was mine, it's one of two at work haha
  14. N

    New "born again chevy guy" from AZ

    hello all, new to the site but not to forums, i know how to search lol also not new to GM's, but so far every gm product ive owned ive managed to blow up in one way or another... hopefully this time around its a different story! i just picked up a 95 K2500. 187k on the odometer, 5.7/4l80e/np241...
See more

Latest posts

Members online

... and 29 more.
Total: 1,733 (members: 79, guests: 1,654)

Forum statistics

Threads
64,366
Messages
1,392,379
Members
51,507
Latest member
LongbedLowLife

Share this page

Top