Recent content by Daniel907

  1. Daniel907

    Potential Bad Ground

    Just an update for those so if someone comes across a similar problem in the future. If you truck experiences issues like I did. Be patient and do your proper diagnostics at the beginning so you can eliminate items that will not be a problem. Granted I purchased another vehicle for a daily...
  2. Daniel907

    Potential Bad Ground

    Additional Update: The truck died last Thursday on the way to work. I have been trying my best to brainstorm what may go wrong, and I came up with Ignition Control Module as well, as symptoms are similar. Replaced it, and no go. So yesterday I dropped the tank and replaced the entire sending...
  3. Daniel907

    Potential Bad Ground

    Update. Truck started up no problem this morning, and ran for a good half hour with no issues. Wipers are functioning properly and all the grounds seemed to check out. The only one that may be questionable is the one on the firewall for the ECU. So hopefully I don't encounter this issue...
  4. Daniel907

    Potential Bad Ground

    Thanks for the locations everyone. I know for sure the battery terminals are fine. I looked those over within the past two months. I'll look through all the grounds and see if I can find an issue. I have a feeling it may be one of the metal grounds going from frame to block/evaporator. Living...
  5. Daniel907

    Potential Bad Ground

    Hello everyone, If this is in the wrong section let me know and I will create a thread in the appropriate section. Here is the issue. The truck is acting funny, started it this morning, and it died after about 10 minutes. The truck would not start again right away. After 5 minutes, it started...
  6. Daniel907

    -8AN or -6AN Fuel Line

    True. I'm also trying to anticipate further modifications in the future, which is why the thought of braided lines sprung to mind.
  7. Daniel907

    -8AN or -6AN Fuel Line

    Hey everyone, 92 K2500, TBI 350 4x4 So the front fuel line on my truck sprung a bit of a leak, which I have come to determine is in the rubber hose. I would rather replace the old hose with AN fittings and braided hose, than pay the $100.00 each for the Dorman replacements at the parts store...
  8. Daniel907

    The Offroad Wheel and Tire Thread

    I run a 265/75/16 on my pickup. Had to raise the front ride height just a touch to account for bumps at full lock. But other than that no issues.
  9. Daniel907

    Best drop in bedliner?

    Why not go for a roll on bedliner, like Herculiner?
  10. Daniel907

    350 TBI is all but done for, so....

    Thats all on you, you could spend the extra money and buy the supplies to learn, and tune yourself. You could find someone local, or even through a tuner like TBI chips (I have no experience or preference for TBI Chips, just the first name that came to mind).
  11. Daniel907

    350 TBI is all but done for, so....

    A big block will be nice to throw in there, but 99'Subourbon laid out a pretty nice price list. Which is reasonable without a doubt, except maybe an Edelbrock performer RPM or Air Gap instead of the Victor Jr., which would more practical as a daily. If you enjoy doing the work, you could find...
  12. Daniel907

    Need New Tires.

    I have a new set of BFG A/T KO2's and the do well in the snow, and surprisingly well on ice, far grippier than expected. Plus the more aggressive sidewall is shweeeet!
  13. Daniel907

    94 c1500 computer tuning questions

    I'm pretty sure that 94 is still OBDI, so learn to burn chips, or swap to a dynamic EFI ECM so you don't have to burn chips anymore. Devs93 thread "Ultimate Toolbox 88-98 ( http://www.gmt400.com/threads/the-ultimate-88-98-performance-toolbox.12428/ ) will explain much of what you are asking...
  14. Daniel907

    Need Moar Loud

    Got some videos. The first is when I just put glasspacks onto the true duals about two years ago. https://youtu.be/GQOCjKv0XMM Here is the current setup that I described earlier. I only went to about 3,000 rpm in this one. Don't want to be too inconsiderate to the neighbors...
  15. Daniel907

    Need Moar Loud

    white_trash88, a set of headers and a decent dual setup will make a world of difference. When I first started tinkering with my exhaust, I first just cut off the stock muffler. Later I put on long tube headers with about 16" of 2.5" ID pipe afterwards with turndowns. (Stupid Loud) What I...
See more

Latest posts

Members online

... and 37 more.
Total: 1,588 (members: 87, guests: 1,501)

Forum statistics

Threads
64,508
Messages
1,395,482
Members
51,852
Latest member
98 tahoe

Share this page

Top