Recent content by 89Sport16

LSX Fuel Pump not Priming

Well, ended up being pretty simple, after metering and not getting a 12V signal at the firewall, I was a bit relived when I put 12V to the fuel pump wire, I was not looking forward to dropping the tank. I worked my way back and found the ground terminal inside the relay connector was pushed...
- 89Sport16
- Post #7
- Jul 3, 2020
- Forum: Engine Performance + Maintenance
LSX Fuel Pump not Priming

The corvette regulator has a return line back to the tank.
- 89Sport16
- Post #5
- Jul 2, 2020
- Forum: Engine Performance + Maintenance
LSX Fuel Pump not Priming

05 5.3 in an 89 C1500, returnless fuel rail with corvette regulator. I did the swap two years ago and used the newer 98 AC Delco pump in the tank. About a month ago, the engine started stumbling on startup, then one day it wouldn’t start and the fuel pump quit priming. I’ve checked the grounds...
- 89Sport16
- Thread
- Jul 1, 2020
- fuel pump priming
- Replies: 6
- Forum: Engine Performance + Maintenance
89Sport

4/6 Ridetech drop kit. It still has a slight rake, Here’s a few more pictures. The tires definitely tuck more in the rear then the front, that might be the reason it may look like it’s higher in the front.
- 89Sport16
- Post #28
- Oct 15, 2019
- Forum: Member Trucks
89Sport

More pictures
- 89Sport16
- Post #25
- Jun 16, 2019
- Forum: Member Trucks
89Sport

Now the new rims and tires, better pictures once the rain stops... Front 20x8 4.75” BS, 245/40R20 Rear 20x9 5.5” BS, 275/40R20 Detroit Steel - Delrays
- 89Sport16
- Post #24
- Jun 16, 2019
- Forum: Member Trucks
89Sport

Here’s an update, truck is back on the road.
- 89Sport16
- Post #23
- Jun 16, 2019
- Forum: Member Trucks
89Sport

The bed is back on.
- 89Sport16
- Post #21
- Mar 29, 2019
- Forum: Member Trucks
89Sport

Thanks, the truck has 114k miles, here’s a pic of the stock interior with the buckets seats, I installed a stock bench seat last year so the kid can ride along.
- 89Sport16
- Post #19
- Mar 27, 2019
- Forum: Member Trucks
89Sport

Thanks! This is my second Sport, I always regretted getting rid of the first one, so when I ran across this one, I couldn’t pass it up.
- 89Sport16
- Post #13
- Mar 26, 2019
- Forum: Member Trucks
89Sport

Brakes are in and it’s on the ground.
- 89Sport16
- Post #11
- Mar 23, 2019
- Forum: Member Trucks
89Sport

New tie rods and idler arm, now I need to get HD brake parts so I can get this wrapped up.
- 89Sport16
- Post #10
- Mar 18, 2019
- Forum: Member Trucks
89Sport

Yeah, that makes sense and I should just get it done now. I’ll be notching the cross member once I get a few people to stand the bed up on the bulkhead. I found a bad idler arm on the front, all the tie rods are pretty crusty, I’m considering replacing both sets of tie rods with the idler arm...
- 89Sport16
- Post #9
- Mar 12, 2019
- Forum: Member Trucks
89Sport

Do I need that, the lower shock mount is already extended?
- 89Sport16
- Post #6
- Mar 11, 2019
- Forum: Member Trucks
89Sport

Started working on the suspension, I finished the rear yesterday, now I’m moving to the front.
- 89Sport16
- Post #3
- Mar 10, 2019
- Forum: Member Trucks