Written up by GoCougs
OK I did the mod today and absoultly love it.
Here is what you need:
1. 1 Relay (4 prong, with #85, #86, #87 and #30. Common relay for aux lights)
2. 16 gauge wire (I used 4 different colors to tell the difference (green, brown, white, yellow))
3. Conduct
4. Electrial tape
5. 1 Self tapping screw
6. 4 female wire connecters
7. 1 Ring terminal for battery
8. 1 Ring terminal for ground
9. 2 side by side wire connectors
10. 1 inline fuse
Step 1
Disconnect the battery at negative and positve ends for safety
Step 2
Remove the passenger side headlight by the 2 bolts on top (or you can remove the marker light, I removed both just for convinence)
Step 3
Clip the brown wire to the brown wire of the low beams
Step 4
Clip the green wire to the green wire of the high beams
Step 5
Run the brown wire from the low beams to the relay. Connecting it using a female adapter to #87
Step 6
Run the green wire from the high beams to the relay. Connecting it using a female adapter to #86
Step 7
Run conduct over both green and brown wires
Step 8
Run a ground from the relay prong # 85 to the screw that holds it on the fender wall
Step 9
Mount the relay near the battery on the passenger side fender using the self tapping screw
Step 10
Run a wire from the relay prong #30 to the battery +, with an inline fuse.
This is how it should look when completed
Step 11
Reinstall the lights, close the hood and flick on your high beams
Low Beams:
High Beams:
OK I did the mod today and absoultly love it.
Here is what you need:
1. 1 Relay (4 prong, with #85, #86, #87 and #30. Common relay for aux lights)
2. 16 gauge wire (I used 4 different colors to tell the difference (green, brown, white, yellow))
3. Conduct
4. Electrial tape
5. 1 Self tapping screw
6. 4 female wire connecters
7. 1 Ring terminal for battery
8. 1 Ring terminal for ground
9. 2 side by side wire connectors
10. 1 inline fuse
You must be registered for see images
Step 1
Disconnect the battery at negative and positve ends for safety
Step 2
Remove the passenger side headlight by the 2 bolts on top (or you can remove the marker light, I removed both just for convinence)
You must be registered for see images attach
Step 3
Clip the brown wire to the brown wire of the low beams
You must be registered for see images attach
Step 4
Clip the green wire to the green wire of the high beams
Step 5
Run the brown wire from the low beams to the relay. Connecting it using a female adapter to #87
You must be registered for see images attach
Step 6
Run the green wire from the high beams to the relay. Connecting it using a female adapter to #86
You must be registered for see images attach
Step 7
Run conduct over both green and brown wires
Step 8
Run a ground from the relay prong # 85 to the screw that holds it on the fender wall
Step 9
Mount the relay near the battery on the passenger side fender using the self tapping screw
You must be registered for see images attach
Step 10
Run a wire from the relay prong #30 to the battery +, with an inline fuse.
You must be registered for see images attach
This is how it should look when completed
You must be registered for see images attach
Step 11
Reinstall the lights, close the hood and flick on your high beams
You must be registered for see images attach
Low Beams:
You must be registered for see images attach
High Beams:
You must be registered for see images attach
Last edited: