Search results

  1. offroadtahoe

    Torsion bar swap and crank

    SAS would have it's own set of problem's and ride would be rough only way to know for sure though would have been to know people with said setup's and to drive around in both setups to see what you like more between all the variables aesthetic's,ride and turning etc.pro's and con's to...
  2. offroadtahoe

    Torsion bar swap and crank

    A dampener does help with wandering and bump's specifically the bilstein version There are a few thing's you could try. Yes as suspension goes downward it would increase postive camber.Are you cranked to 6" how far from the bump stops? you could crank more and it will get you back in range to...
  3. offroadtahoe

    Torsion bar swap and crank

    check out my post in this thread https://www.gmt400.com/threads/2-4-inch-lift-upper-control-arms-for-96-k2500-8600gvw-8-lug.66717/#post-1399311 and this thread https://www.gmt400.com/threads/control-arms-for-lifted-trucks.65842/page-2#post-1381142 you also will need longer shock's if you crank...
  4. offroadtahoe

    Frankenstein ? K2500 8600 gvw mismatched lower control arms

    Yes
  5. offroadtahoe

    Frankenstein ? K2500 8600 gvw mismatched lower control arms

    welded forged end control arm use a 46.13mm ball joint.the forged control arms are press in as well and are a upgrade and use a little bigger 47.89mm ball joint they supposedly increase turn radius i know i felt a bit of difference. i know knuckles changed after a certain year that's why you...
  6. offroadtahoe

    Trackmotive CV joints.

  7. offroadtahoe

    K1500 8.25 to 9.25 swap

    you can keep 6-bolt hub's the 9.25 cv's are bigger but are bolt in And you can use your k1500 upper control arm,k2500-k3500 upper control arm's are wider at the mount's and would need the frame mounts cut/welded. you can run any of the 3 different lower control arm's.(stamped steel bolt in...
  8. offroadtahoe

    Front end rebuild

    The gvw doesn't matter.k1500-k3500 all use one of the 3 types I listed,you go by what type lower control arm's you have. check back on my previous post added pics and more details
  9. offroadtahoe

    Front end rebuild

    With the light duty 6-lug 2500's making things confusing It's easier to go by this for k-series (4wd) Gvw does not matter.There are only 2 different upper ball joints and 3 different lowers ball joints for these trucks *The 6-lug uses a different upper ball joint then the 8-lug * 6 and 8 lug...
  10. offroadtahoe

    Nv4500 swap

    Also there is a master cylinder upgrade check it out https://www.gmt400.com/threads/perfection-clutch-master-cylinder-upgrade.11658/
  11. offroadtahoe

    Nv4500 swap

    4:50 for visual and 1" 3/8 for the center hole 23/64 for the bolts
  12. offroadtahoe

    Nv4500 swap

    Are you trying to cut the hole for it?
  13. offroadtahoe

    Front end rebuild

    yes they are bilstein 33-174525 here is a thread on it for some more details https://www.gmt400.com/threads/cognito-braces-and-steering-dampner.60499/#post-1363719
  14. offroadtahoe

    Front Diff bushings and diff bracket bushings

    These are the diff bushings.https://www.rockauto.com/en/moreinfo.php?pk=10372812&cc=1303614&pt=10403&jsn=415 no info on the A-arm bushings
  15. offroadtahoe

    steering wheel alignment

    set screw has to be on the bottom,otherwise it will not be orientated correctly to get it perfectly straight read through this thread https://www.gmt400.com/threads/cunningham-machine-upper-lower-steering-shafts.60253/page-4
  16. offroadtahoe

    88-98 parts

    Think so I keep reading they got a higher spring rate
  17. offroadtahoe

    88-98 parts

    Can ship at buyers expense paypal 3 % vertical fog light switch with bezal (no pigtail) 80$ Stock upper control arms with Prothane bushings,Stock lower control arms forged end with prothane bushings 100$ Tahoe z71 T-bars 80$ Front Aluminum splash guard 80$ T-case or front diff aluminum guard...
  18. offroadtahoe

    14 bolt sway bar mounting

    yes i can mount it higher,but then the bar pushes downward,needed shorter or a set of adjustable endlink's to have both just right but haven't gotten around to it
  19. offroadtahoe

    Anyone Tried Cunningham OBS- tie rod sleeves

    My knowledge on 2wd is limited but i do know you can run the kryptonite pitman,upper ball joints (most articulation) not sure if ttx is the same but kryptonite show a photo comparison of moog etc. and that stock 4wd forged upper control arms are a upgrade for 2wd stamped steel.so the upper...
  20. offroadtahoe

    2-4 inch lift Upper control arms for 96 k2500 8600gvw 8 lug

    Check out this thread. https://www.gmt400.com/threads/extended-upper-control-arms.33481/ I'm not sure if he tried to run these without the lift and had the same problem as with the lift.the fix might have been to crank more to get where you can get in range to adjust the camber to spec,But it...
  21. offroadtahoe

    Lifts

    I don't know if superlift or tuffcountry are 4" lifts and crank for the rest.just like rough country but there is FTS (full throttle suspension)
  22. offroadtahoe

    Torsion bar hex size?

    I'll get some measurements for u in the morning have a set sitting around,
  23. offroadtahoe

    Rear sway bar - adco 214

    check out this thread on mounting a hellwig rear sway bar on a 14bff pics in last post i used stock endlink mounting locations and bought a mount for the sway bar ends. https://www.gmt400.com/threads/88-98-4wd-front-sway-bar-upgrade.59152/#post-1258211
  24. offroadtahoe

    14 bolt sway bar mounting

    I used hellwig it comes with the mounting brackets and just used the stock mounting for the endlinks instead of the end link mounts it came with and bought brackets for the swaybar to mount. hidden far in the search page here is the thread on front sway bar info and and rear with pics on a 14bff...
  25. offroadtahoe

    Anyone Tried Cunningham OBS- tie rod sleeves

    Just a plus no cons on these same on the adjustable,posted about these before somewhere,easy to adjust and definitely feels solid mainly low speed turning with 38.5"s also running ttx tierod's and they are doing awesome,I will be be upgrading to kryptonite for peace of mind though.

Latest posts

Staff online

Members online

Total: 1,396 (members: 47, guests: 1,349)

Forum statistics

Threads
65,108
Messages
1,405,839
Members
53,144
Latest member
Knighter17

Share this page

Top