Carnage and Stuck Pics

[1996 yukon]

Post up your carnage and stuck pics here. Feel free to share stories, but you know how the forums work - pics or ****!

You must be registered for see images attach

You must be registered for see images attach

 

[Bighead38]

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

Pulled it out with:

 

[Butch]

You must be registered for see images attach

my old rig

 

[bggrnchvy]

You must be registered for see images attach

Snapped a coilover shaft on Tank Trap.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

Fragged my 80e and had to rebuild it.

You must be registered for see images attach

Wasted the front driveshaft 4 times now, 2x the CV failed (now a 1350CV), one time I ripped the tube in half and the last time I ground 2 caps worth of 1310 needle bearings into anti-seize looking paste.

 

[88GMC]

Wheeling trip from a while back. First time out in the 88', Steep hill, wet rutted clay, bald ATs, entirely too much wheel speed = New character in the bedside, an overheated motor and an angry T-case. The addiction started.

The truck just sat in the same place and spun all 4...

You must be registered for see images attach

You must be registered for see images attach

My buddy got the worst luck award for the trip. The kid that washes and polishes his Rubi everyday decided to take it out for the first time after some coaxing...

You must be registered for see images attach

You must be registered for see images attach

Cracked the hardtop, wadded both flairs, and put some nice dents and scratches in her.

 

[Greg]

that rubi pic made me lol
thank god i havent had too much damage to my truck.
hunting tore off part of my valance. that was about it lol.

 

[chevy_man]

my rockers aren't exactly un-touched anymore after playing in some gravel piles

You must be registered for see images attach

and I don't know where this dent came from. It wasn't there all winter, but when I washed it in the spring WHAM! New dent. I just make it a point now to keep at least 1" of mud on the truck so that most of the dents and paint don't show.

You must be registered for see images attach

And the classic, make your buddies dig it out

You must be registered for see images attach

this is why I got stuck, I had to stop because of this jackass. I didn't feel like driving 20 miles around to the other side so I tried to crawl through a 200 yrd long drift. Didn't work. After I put the chains on and let them dig a bit it popped right out.

You must be registered for see images attach

 

[FUNINMUD]

Couple older ones. Had lifted the truck but didn't get new tires yet so out with a cepek lift + 2"bl and 285/75R16 bfg's High centered.

You must be registered for see images

Even older, had went around a different way and was backing up to give a pull, snow looked level but it turned out the snow was hiding a big hole.

You must be registered for see images

 

[Cajun4x4]

10 bolt didnt like 150 lbs of tire and rim per corner

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

spindle looked a lot like this, but worse...

You must be registered for see images attach

broken center pin

You must be registered for see images attach

You must be registered for see images attach

failed welds and ****** aluminum shaft

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[JayBo]

Oh hayyyyy!!

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach