Search results

  1. chevyman("

    "Under the Hood" Pics.....What have you done?

    made me a cold air box and channeled it through the hole in my fender i think it looks pretty dang good lolhttps://scontent-b-mia.xx.fbcdn.net/hphotos-xpa1/v/t1.0-9/558160_629734410374871_908621827_n.jpg?oh=db5bf809f89d2f163285db60fb72e69d&oe=544CF024
  2. chevyman("

    Cammed vortec doesnt start without opening throttle!?!

    Well i have about 2000 miles on it now and we still havent corrected the startup issue it idles great and runs great lol my injectors are at 102% duty cycle so since my buddy is a fast dealer were gonna be using a single plane from fast with ls3 injectors and the fast 1000cfm throttle body with...
  3. chevyman("

    anyone running long tubes/ mid length headers??

    http://www.ebay.com/itm/Chevy-GMC-88-95-Truck-Black-Coated-Mid-Length-Headers-305-350-5-0L-5-7L-TBI-/251504806321?pt=Motors_Car_Truck_Parts_Accessories&hash=item3a8edac9b1&vxp=mtr im running these in my 2wd 97 silvereado and i love them nice 3/8 flange all tigged pipes very good quality for the...
  4. chevyman("

    Cammed vortec doesnt start without opening throttle!?!

    Hi i have a mildly built 350 vortec .30 over h beams forged crank 10.1 CR 500 lift cam 220/224 110lsa cam and it will not start without applying throttle if i hit the key it will bump a few times then die right after! Need some help guys i swapped the 0411 into it and lexitech hooked me up with...
  5. chevyman("

    Need some opinions on my built 350 vortec!

    Heres my cam card Vortec powered iphone:D
  6. chevyman("

    Need some opinions on my built 350 vortec!

    Hey guys i just finished building a 350 vortec for my truck.. Long story short i have 0.30 speed pro flat tops in it its calculated out to be 9:91 so i think basiclly 10:1 compression would i be ok running 93 octane from experience does a 10:1 motor run pretty good on pump gas? 93 of course...
  7. chevyman("

    Burnout pics/videos thread...

    here goes an old one!https://www.facebook.com/photo.php?v=812508508764126&set=vb.100000149531708&type=3
  8. chevyman("

    Burnout pics/videos thread...

    here goes and old one!https://www.facebook.com/photo.php?v=812508508764126&set=vb.100000149531708&type=3
  9. chevyman("

    0411 swap ?

    Has anyone else had the one ground wire that just makes a loop it has 2 ends yellow and black it shows it to be pinned in pin 1 of c2.. So i just ground this one? Vortec powered iphone:D
  10. chevyman("

    Cammed 1999 Chevy Tahoe idle problems

    Probably the iac valve it has to have a certain range of motion if they tuned the iac valve to where it cant correct for the big surges a cam with high duration makes like it reaches max opening and it's not enough to correct the idle it wont idle proper make sure the is valve is working...
  11. chevyman("

    The Center Console Thread

    my console.. Amazing cup holders lol Vortec powered iphone:D
  12. chevyman("

    Considering dong an LT4 Hot cam

    Ive been reading alot about this.. Im gathering parts myself the hardest part would be getting it dialed in properly Vortec powered iphone:D
  13. chevyman("

    From blackbox to 0411??

    Hey guys i have a 98 silverado l31 bored .60 eagle rods stock crank marine cam 1:6 rockers lil port an polish.. 4:10 gears.. E fan and lots of goodies also a tune, What would the 0411 do for me besides a higher rev limiter dual tables etc with all the mods i have? Vortec powered iphone:D
  14. chevyman("

    Cranks but she wont start.

    Id say 80% of the time its the sending unit in the tank.. It has to hold constant pressure on the injectors. If you have the oem poppet injectors they will not fire if they dont have sufficient pressure.. My 98 did the same exact thing as yours and it was the sending unit.. Make sure the motor...
  15. chevyman("

    Flexplate ticking

    Guess what lucky your right lol here she is Vortec powered iphone:D
  16. chevyman("

    Flexplate ticking

    Ok ill take a see at the bolts guys Vortec powered iphone:D
  17. chevyman("

    98 silverado long tubes

    98 silverado l31 i jave flotech shorties right now and im really wanting some longtubes because i know theyll help me but i only have the sensors on bank 1 an 2 no EGR or rear 02 sensor.. Will any.. Any of the older headers for c10's and such or something fit in my truck.. I can weld o2 bungs...
  18. chevyman("

    Oh no...I think the 350 may be dying

    Rod knock for sure my l30 sounded the same when it spun the #1 Vortec powered iphone:D
  19. chevyman("

    Flexplate ticking

    No its a ticking sound like metal on metal its not constant thou it can change with rpm changes Vortec powered iphone:D
  20. chevyman("

    Flexplate ticking

    It flew apart? Vortec powered iphone:D
  21. chevyman("

    Flexplate ticking

    Hmm but this starter is new and its been on there about 6 months and the ticking only started with this trans Vortec powered iphone:D
  22. chevyman("

    Flexplate ticking

    Hey guys, 98 silverado l31/4l60e I put a trans in it about a month ago and ever since its had this periodic tick/rattle noise coming for sure from the bellhousing area.. It only does it at idle to about 1000-1500 rpm if i hit the gas a sec i can usually make it do it but not always.. Is my...
  23. chevyman("

    she wonders on the road??

    it has brand new nexen 305/40/22's so its not tire wear and a new pitman arm and idler but the rest is all original.. maybe its time to go for an alignment
  24. chevyman("

    Lt4 hotcam in my 98... Ive searched!

    Hmm sounds good guess i just need to start gathering parts Vortec powered iphone:D
  25. chevyman("

    she wonders on the road??

    Just a 2" drop in the rear stock in the front and it drives pretty straight for the most part just wonders very easily if i let go of the wheel itll pull to one side or the other depending but with my stock wheels it doesnt .. I was just wonderig if you guys had and secrets up your sleeve lol...
Top