Search results

  1. Bryan Dees

    94 LS Swap

    I cant seem to find anything on there pre 96, at least there is nothing labeled pre 96 for these trucks. Lots of stuff on older cars and such.
  2. Bryan Dees

    94 LS Swap

    http://www.lt1swap.com/gmt400swap /index.htm This link will take you to the 96+ information.
  3. Bryan Dees

    94 LS Swap

    Wondering if anyone has any info about marrying the wiring harnesses together from the LS to the factory harness? I can find 96+ but nothing for a 94 etc. If anyone could point me in the direction of a how to guide, that would be great. LT1Swap is also 96+, nothing there on a 94 down. Thanks!!
  4. Bryan Dees

    5.7 build sheet

    Worst I’ve ever seen. You can see the discoloring on the block where that main got super hot. I’ve never seen one crack the block under the main bearing either. I knew that’s where the issue was when the bolts on that one main cap were only finger tight. So now I have heads and a trans for...
  5. Bryan Dees

    5.7 build sheet

    Thanks for the info! I’m not going to be doing anything to the 92 engine. I put it back together, found the squeal and fixed that, then I was able to hear the knock in the bottom end. Tore it down and found spun rod bearings, and three spun mains. Check the photos of the block, crank and mains.
  6. Bryan Dees

    5.7 build sheet

    Good info guys. I already had the thing ready to pull. Was going to snatch it out tonight. I bought the truck as a donor for my 94, never could sell it because of the squeal. Maybe I will connect all the wiring back up and fire it up and see if I can figure out what’s going on before I pull it...
  7. Bryan Dees

    5.7 build sheet

    Thanks for the info Schurkey. It doesn’t have a knock, it has an intense his pitch squeal after it runs for maybe 45 seconds.
  8. Bryan Dees

    5.7 build sheet

    Ok so I have a question for the engine builders. I currently have a 94 and a 92 both with 5.7’s. The 92 has a suspect spun rod bearing and the 94 runs great. I’m about to pull the 92 and do a rebuild, and had plans to LS swap the 94. After some thought I felt that for headache reduction, when I...
  9. Bryan Dees

    2/4 or 3/4 Drop Kit, what size tires for Rally 15"s?

    Thanks Richard! I'm guilty of not reading the whole thread, I just replied to Sewlow's post. That makes me feel better about the DJM kit.
  10. Bryan Dees

    2/4 or 3/4 Drop Kit, what size tires for Rally 15"s?

    Sewlow, DJM claims that their LCA's paired with their UCA's remove all camber, castor and bump issue and ensure a "stock" ride experience. They also claim that with both of those in place alignment isn't an issue. I was wondering if you knew of anyone that has this particular setup, or if...
  11. Bryan Dees

    Fast blinkers

    Purchased a heavy duty flasher today, went to the parking lot and installed it, soon as I turned the key on, the blinker fuse blew. Took it back inside, got the factory replacement and a new fuse, installed both, fast blinker issue resolved. Thanks for all the input!
  12. Bryan Dees

    The real differences in 700r4/4l60/4l60e transmissions by year

    All that being said, one can assume that a 700R4 from a 92 extended cab will not work in a 94 single cab. But...are the torque converters interchangeable? Mine hits really hard from 1st to 2nd and when going from park to drive or reverse.
  13. Bryan Dees

    94 MarkIII buckets to 60/40 bench

    Got it bolted in today, really liking the new seats. Made the truck feel a lot better on the inside. Thanks for the info Mac, helped me a TON!!
  14. Bryan Dees

    94 MarkIII buckets to 60/40 bench

    I was thinking about putting some clear bathroom caulk on the bottom side between the washers and the floor when I put them in. Ended up working late today, so I will have to wait to bolt them in. Supposed to be getting some bad weather here in the next few days, hopefully I can get it done...
  15. Bryan Dees

    94 MarkIII buckets to 60/40 bench

    Got it cut down and welded up today. Going to drill hole and bolt it in tomorrow hopefully.
  16. Bryan Dees

    94 MarkIII buckets to 60/40 bench

    That looks really nice! I went out earlier and sat the 60 side in and saw exactly what you were talking about. Going to get the metabo and welder out in the morning if the weather holds off and do the same thing. Thank you for the info, huge help!
  17. Bryan Dees

    94 MarkIII buckets to 60/40 bench

    What was the need for the bracket modification? Do you remember how much room you had between the trans and the tunnel, or did you pull the trans to install the bolts?
  18. Bryan Dees

    94 MarkIII buckets to 60/40 bench

    Has anyone made the swap? The MarkIII buckets sat on a single frame held down by 4 bolts. Two on the drivers side, and two on the passenger side. The 60/40 seat is a little different. The drivers side (40) portion, will bolt right in because there are already bolt holes for the bucket base. The...
  19. Bryan Dees

    Fast blinkers

    Thanks for all the info, I am going to buy a new flasher relay and see if that fixes the issue.
  20. Bryan Dees

    Fast blinkers

    I didn’t think about the flasher relay. Now I want to turn the emergency flashers on and see how fast they flash.
  21. Bryan Dees

    Fast blinkers

    Thanks Garrett. I think I have an electrical issue. It is a MarkIII truck with those crappy interior lights. I have removed all of those and I’m thinking the electrical system doesn’t like it.
  22. Bryan Dees

    Fast blinkers

    Ok so I put new headlights in today. Installed all new headlight bulbs, blinker bulbs, running lights, and corner marker bulbs. Blinkers blink fast like there is a bulb out, but there isn’t, with the running lights on, the blinkers light up as well. With headlights on, all the bulbs on the front...
  23. Bryan Dees

    New to GMT400

    Hello, Wanted to introduce myself. I am Bryan, I'm from Saraland, AL which is about 10 minutes north of Mobile. I recently purchased a 1994 MarkIII conversion truck that has had all the body molding and wood trim in the interior removed. I am working on putting this thing back together without...

Latest posts

Staff online

Members online

Total: 1,031 (members: 14, guests: 1,017)

Forum statistics

Threads
64,487
Messages
1,395,035
Members
51,791
Latest member
WrenchAndRatchet

Share this page

Top