Recent content by Torchred
-
95 Silverado Build
I don't think I've used that since like 2016- Torchred
- Post #518
- Forum: Member Trucks
-
95 Silverado Build
still have to order some tires for it. Thinking about doing some daily driver, hard tire stuff with the truck. Just have to decide on something :hahano:- Torchred
- Post #516
- Forum: Member Trucks
-
95 Silverado Build
Also just had a full 3" stainless exhaust done with V bands, much better than the homemade exhaust I had on it for a year.- Torchred
- Post #514
- Forum: Member Trucks
-
95 Silverado Build
Well I broke the 4l60e, no surprise. Having a 4l80e built right now with red clutches and a transgo HD2 kit. Ordered an FTI 3600 stall as well. What more than likely broke my trans Also got new wheels vs running the camaro wheels, doing 17x4.5 front and 15x10 rears. Should look pretty sick...- Torchred
- Post #513
- Forum: Member Trucks
-
95 Silverado Build
Onto the next stage for the truck, 2010 Camaro wheels, already picked up a set of Firestone Firehawks for them, still had the original 2009 date coded Pirelli tires. Flip kit, drop springs, 90/10 shocks, and Speed Engineering traction bars. See if I can make this thing 60ft better.- Torchred
- Post #512
- Forum: Member Trucks
-
95 Silverado Build
Always wanted to do and drag and drive event, decided to take the truck on one in October with my best friend. Truck had less than 150 miles on the swap so we towed it from Charleston SC to Greer SC with my buddy's first gen. Truck did really good for what it being basically a cam only lq4...- Torchred
- Post #511
- Forum: Member Trucks
-
95 Silverado Build
I'll look into it, appreciate it. The front crossover will get redone soon one way or the other. Need to pull 3" or so in-between the bends and it'll be a lot better.- Torchred
- Post #510
- Forum: Member Trucks
-
95 Silverado Build
Bought an ebay tubing kit, no pipe bender. First time building an exhaust so there are a few improvements to make .- Torchred
- Post #508
- Forum: Member Trucks
-
95 Silverado Build
Well finally got it driving, needs some help on the tune but she'll be ready to rip soon.- Torchred
- Post #506
- Forum: Member Trucks
-
95 Silverado Build
Nothing much new going on, just chipping away at it. Wired up my switch panel, it's gonna live below the HVAC stuff New Forever Sharp steering wheel, this things sick Gauges look great inside with the doors shut and the tint being dark is Also redid the fuel system, using a Holley...- Torchred
- Post #504
- Forum: Member Trucks
-
95 Silverado Build
Glowshift oil pressure and coolant gauges, my inner ricer has always wanted these that sweep when you cut the key on. Going into a pillar pod- Torchred
- Post #503
- Forum: Member Trucks
-
95 Silverado Build
I kept everything related to the factory fuse block and cut basically the entire engine harness out of it, kept the starter signal, a/c wiring, and a few other things. LS is on a standalone, I think I had to do more to wire my gauges than to power the engine harness.- Torchred
- Post #502
- Forum: Member Trucks
-
95 Silverado Build
Not on here as much as I should anymore, been working on it 2ish yrs little by little, raised in the paint and body industry so it was a pretty big learning curve and took a hot min to get to this point. If your talking power steering, using the 95 lines and box to the nbs non evo pump. May be...- Torchred
- Post #500
- Forum: Member Trucks
-
95 Silverado Build
Well the little 6 liter fired off for the first time on Sunday, that Texas Speed cam has all the chop to it.- Torchred
- Post #498
- Forum: Member Trucks
-
95 Silverado Build
Well she looks like a truck again, still have to finish wiring the engine and run a few fuel lines. Front end is up around 2" with this drivetrain in it, level it once its running.- Torchred
- Post #497
- Forum: Member Trucks
