Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
offroadtahoe's latest activity
offroadtahoe
reacted to
Caman96's post
in the thread
Anyone Tried Cunningham OBS- tie rod sleeves
with
Like
.
I’ve got them with TTX tie rods. :waytogo:
Apr 12, 2024
offroadtahoe
replied to the thread
Anyone Tried Cunningham OBS- tie rod sleeves
.
My knowledge on 2wd is limited but i do know you can run the kryptonite pitman,upper ball joints (most articulation) not sure if ttx is...
Apr 12, 2024
offroadtahoe
replied to the thread
2-4 inch lift Upper control arms for 96 k2500 8600gvw 8 lug
.
Check out this thread. https://www.gmt400.com/threads/extended-upper-control-arms.33481/ I'm not sure if he tried to run these without...
Apr 12, 2024
offroadtahoe
reacted to
fancyTBI's post
in the thread
Anyone Tried Cunningham OBS- tie rod sleeves
with
Like
.
https://www.gmt400.com/threads/heavy-duty-tie-rod-sleeves.57702/ there’s a whole thread on them.
Apr 11, 2024
offroadtahoe
replied to the thread
Lifts
.
I don't know if superlift or tuffcountry are 4" lifts and crank for the rest.just like rough country but there is FTS (full throttle...
Apr 11, 2024
offroadtahoe
replied to the thread
Torsion bar hex size?
.
I'll get some measurements for u in the morning have a set sitting around,
Apr 11, 2024
offroadtahoe
replied to the thread
Rear sway bar - adco 214
.
check out this thread on mounting a hellwig rear sway bar on a 14bff pics in last post i used stock endlink mounting locations and...
Apr 11, 2024
offroadtahoe
replied to the thread
14 bolt sway bar mounting
.
I used hellwig it comes with the mounting brackets and just used the stock mounting for the endlinks instead of the end link mounts it...
Apr 11, 2024
offroadtahoe
replied to the thread
Anyone Tried Cunningham OBS- tie rod sleeves
.
Just a plus no cons on these same on the adjustable,posted about these before somewhere,easy to adjust and definitely feels solid mainly...
Apr 11, 2024
offroadtahoe
reacted to
nicksuspect's post
in the thread
Does anyone know what bushings these are near the lower control arms? Possible part number/s?
with
Like
.
Have you had any luck finding replacement.
Apr 8, 2024
offroadtahoe
reacted to
A97obs's post
in the thread
Cunningham Machine Upper/Lower Steering Shafts?
with
Like
.
It Drives good ! Take into consideration it takes 20 years for a was joint to wear to nothing and the slop on a new one is extra minimal...
Apr 7, 2024
offroadtahoe
reacted to
ColoradoChevyGuy87's post
in the thread
97' k1500 DD/crawler/prerunner/overland build
with
Like
.
How's the build holding up? How much travel did you end up with?
Apr 6, 2024
offroadtahoe
reacted to
A97obs's post
in the thread
Anyone make better stabilizer bracket “U bolts” for 2wd bolt on Steeing stabilizers ?
with
Like
.
Thanks “lol … So much fun trying to avoid the naysayers who can’t wait to weigh in on why did you lift your 2wd .. it’s like wtf why...
Apr 3, 2024
offroadtahoe
replied to the thread
96+ GM109SS Lower Steering Column Bearing UPGRADE!
.
88-94 old style dash https://www.wolffeng.com/store/p2/M109SS_Lower_Steering_Column_Cartridge_Bearing.html New style dash 96-98+...
Apr 2, 2024
offroadtahoe
reacted to
A97obs's post
in the thread
Cunningham Machine Upper/Lower Steering Shafts?
with
Like
.
It was actually easier to leave it below. 88-94 tbi trucks have little to nothing above the drive side frame rail. In my case being a...
Apr 1, 2024
Latest posts
Full-Page ads taking over forum???
Latest: Caman96
6 minutes ago
Feedback, Help and Suggestions
The build of "Wh4t3v3rs"
Latest: Wh4t3v3rs
25 minutes ago
Street Build Threads
Camper Top Combatability between GMT 400 vs 800?
Latest: someotherguy
33 minutes ago
Paint / Body / Detailing
Rough at high speeds
Latest: RichLo
33 minutes ago
Engine Performance + Maintenance
daytime headlights
Latest: 99xcss4
35 minutes ago
Audio + Electronics
Staff online
kennythewelder
Officially Retired, B31-3 (6-G) certified welder.
Members online
kennythewelder
Caman96
TheDogsSuburban94
Obsbray
Schurkey
PCMusicGuy
lit549
squeasel
Machlen
99xcss4
Road Trip
Komet
TylerA245
fancyTBI
4x4animalstyle
alabbar
1998_K1500_Sub
ivankelly
rangokatt
97-2door
WojTec
SerStarfish
mxmxmc3000
Minn95Dually
Nad_Yvalhosert
Connorpod
CFS176
Rexall
THE CALI FLASH
JPVortex
Ryanstokes8
GrimsterGMC
Austindarksaber
Teddysvam
SNCTMPL
NCroger
Carlaisle
IndexOf0
Aqua-pig
scott2093
Supercharged111
Zack8
whewshikaw
Alteca
SuperSpore
someotherguy
Wh4t3v3rs
Drunkcanuk
billmack7
WrenchAndRatchet
... and 4 more.
Forum statistics
Threads
64,550
Messages
1,396,353
Members
51,975
Latest member
Machlen
Share this page
Facebook
X (Twitter)
Reddit
Pinterest
Tumblr
WhatsApp
Email
Share
Link
Members
Top