Recent content by hefftone

  1. H

    Draw Tite for trucks w/ roll pan

    I'll post up weight and dimensions with my zip 30132. You can submit All best offers + shipping (with your carrier specification .) Great piece, replaced my beat up roll pan with a 99 chrome bumper.
  2. H

    Tool for lowering the spare?

    I have the ratcheting part for the jack, the tube with a hex and a hook, for the jack......don't have the jack, don't have the part that goes through the bumper and into the "spare tire picker uppper thing." Lol, what does it look like? Lol, wtf is this stuff called? Pic of said tool wins.
  3. H

    Why does my power window stop 3 times?

    I decided not to devle into pandora's box....at the warning of others.
  4. H

    Draw Tite for trucks w/ roll pan

    Bump, let's make a deal on this thing!
  5. H

    Xj steering shaft

    Hey where you at in Georgia? My truck needs in of these bad!
  6. H

    Draw Tite for trucks w/ roll pan

    I'm in Georgia, what state are y'all in? Maybe we can hook it up. Omg, the losers on craigslist are killing me.
  7. H

    Draw Tite for trucks w/ roll pan

    Good looking out man! I'll have to edit the post.
  8. H

    Draw Tite for trucks w/ roll pan

    Up for sale is a Draw-Tite hitch receiver, for GM/Chevy fullssze truck....for use with trucks with roll-pan. This for 1988-2000 c1500/k1500 trucks, blazers etc. . DrawTite 41522 5000 tow/ 500 tongue UPC...742512415223 It comes with the bolts/hardware. No hitch. No wiring.But you can probably get...
  9. H

    Summer Wishlist

    Intake tube? I might....
  10. H

    Bumper & Bed ...interference

    When I got my truck it had a roll pan. It was beat all to so I cut it off. I also had to take the bed off several times to deal with fuel tank,sender, and pump issues. A couple years ago I snagged a rear bumper from a 97 that had the bed removed. It sat until now, when I finally enlarged two...
  11. H

    Help! Oil pressure sender just broke off!

    Yes. It is an Autozone Valucraft... not sure of the #, but it is a 3-pin...and longer than the 2-pin i removed. No, but I plan on doing that. No I don't have another cluster. My brother said that the gauge used to work right up until the engine replacement. Now that makes sense because the...
  12. H

    Help! Oil pressure sender just broke off!

    I've made some progress, but still have some issues. To replace to brass elbow, I used a 1/8" NPT Nipple (1-1/2" Long), out of the block into (the side of)a 1/8" NPT Female Tee. Out of what should be the bottom of the tee, a 1/8" to 1/4" NPT Reducer to accept the new oil switch/sender. Then...
  13. H

    HVAC controller button fix? 1990

    The hvac buttons controlljng fan speed, defroster, heater, and vent have stopped working. Is this a common problem? Can it be opened and have the switch contacts cleaned? Tapatalk 2
  14. H

    Help! Oil pressure sender just broke off!

    Karma.... Could not start engine until I jumped out the FP relay. Then conked out at a traffic signal, and had to do it again. As I am understanding, the oil pressure switch/sender would have kept it running...if this is a dying FP relay. The engine in my truck actually came out of an earlier...
  15. H

    Help! Oil pressure sender just broke off!

    I was replacing the sender hoping that would fix my gauge issue. In the mornings lately, the check gauges light has been coming on for a few seconds to a few minutes. But its doing the same thing without any sensor installed. Sent from my SGH-I897 using Tapatalk 2
See more

Latest posts

Staff online

Members online

... and 19 more.
Total: 1,593 (members: 69, guests: 1,524)

Forum statistics

Threads
64,434
Messages
1,393,963
Members
51,660
Latest member
david1994gmc

Share this page

Top