Recent content by AuroraGirl

Anyone have experience with gmt800 trucks?

plus i dont intend to get it covered in mud and road salt then leave it that way I dont plan to do brake jobs without evrer using any brake lube. etc. lol.
- AuroraGirl
- Post #69
- Today at 5:40 AM
- Forum: Other Vehicle Builds
Anyone have experience with gmt800 trucks?

So I didnt take many pics once I got things together, but without an assistant to bleed I think i did a pretty good job (could tell it needs bit of a bleed but still good otherwise). The passenger rear I think im going t o spring for a new rotor and pads because the driver side is almost new...
- AuroraGirl
- Post #67
- Yesterday at 9:32 PM
- Forum: Other Vehicle Builds
Anyone have experience with gmt800 trucks?
- AuroraGirl
- Post #66
- Yesterday at 9:27 PM
- Forum: Other Vehicle Builds
Anyone have experience with gmt800 trucks?

This wasnt so bad
- AuroraGirl
- Post #62
- Monday at 6:34 PM
- Forum: Other Vehicle Builds
Anyone have experience with gmt800 trucks?

it was given to me by my stepdad, 1) im cheap 2) I dont intend to artificially extend its life span (no frame off resto) and 3) it would be offensive (not in my eyes, but other peoples) to sell and replace the vehicle I was gifted.
- AuroraGirl
- Post #61
- Sunday at 4:31 PM
- Forum: Other Vehicle Builds
Anyone have experience with gmt800 trucks?

Even with safety glasses the rust just falls in your face. As soon as I finish installing my outdoor hose I’m going to get the pressure washer and at least remove the flakes that are in such large amounts. It may sctually rust slower removing the rot like that lol
- AuroraGirl
- Post #59
- Sunday at 1:08 PM
- Forum: Other Vehicle Builds
Anyone have experience with gmt800 trucks?

note to self., when step dad says "he fixed the wiring to the rear properly" assume properly means poorly lol.
- AuroraGirl
- Post #56
- Sunday at 12:12 PM
- Forum: Other Vehicle Builds
Heavy Duty Tie Rod Sleeves

what thread size are the sleeves? I wonder if other make trucks use similar threads for their tie rods?
- AuroraGirl
- Post #16
- Saturday at 10:46 AM
- Forum: Cunningham Machine
Heavy Duty Tie Rod Sleeves

i thihnk thats just boilerplate aftermarket Cover your a*s terminology used by a lot of companies. Possibly gets them out of certain regulatory nets
- AuroraGirl
- Post #14
- Friday at 7:07 PM
- Forum: Cunningham Machine
Rev limiter

I found my own post by doing a google search on KKD0, if anyone cared to know, I did find out the knock sensor, as of 1996 so presumably all the years of the EFI 4.9, DOES do something. Detecting knock, it pulls 4 degrees of timing. Specifically, 4° between 1100 amd 3800 rpm at full...
- AuroraGirl
- Post #79
- Friday at 12:09 AM
- Forum: Engine Performance + Maintenance
Really wish ppl would stop bringing me trucks with hydraulic fluid in trans
- AuroraGirl
- Post #522
- Apr 30, 2024
- Forum: Transmissions
Really wish ppl would stop bringing me trucks with hydraulic fluid in trans

GET THE **** OFF MY OBSTACLE
- AuroraGirl
- Post #514
- Apr 27, 2024
- Forum: Transmissions
Really wish ppl would stop bringing me trucks with hydraulic fluid in trans
- AuroraGirl
- Post #501
- Apr 23, 2024
- Forum: Transmissions
Really wish ppl would stop bringing me trucks with hydraulic fluid in trans

No thats for fixing these
- AuroraGirl
- Post #459
- Apr 21, 2024
- Forum: Transmissions
Really wish ppl would stop bringing me trucks with hydraulic fluid in trans

Whbile we are gathered here, any thoughts on sealing the seam strip on this topper? I have a thread on it but you all seem to have time so im making you a captive audience.
- AuroraGirl
- Post #448
- Apr 21, 2024
- Forum: Transmissions