Recent content by 04silvy

  1. 04silvy

    The never ending bagged and bodied 90 rcsb build....

    The rear is setup to lay out on a 31" tall tire. So I was going to run 265/35/22s. I had a set of 22s on the wife's ride with that size tire and it road pretty good. That's about as low of a profile as I want to run around my area. We don't have the greatest of roads around here. Front...
  2. 04silvy

    The never ending bagged and bodied 90 rcsb build....

    Also did a notch cover finally. Goes with the theme... Once again..crappy photo from the selfie cam... Sent from my HTCONE using Tapatalk
  3. 04silvy

    Lester622 build thread

    I like it! Very clean! Sent from my HTCONE using Tapatalk
  4. 04silvy

    The never ending bagged and bodied 90 rcsb build....

    Thanks man. Still loving it. Actually about to throw full coverage back on it so I can drive her again. Hows your truck coming along btw? Need to get the driveline vibration fixed and all will be good. Didn't find anything loose or bad on it when I went through it other than the rear link...
  5. 04silvy

    New project/tow pig

    Sent from my HTCONE using Tapatalk
  6. 04silvy

    The never ending bagged and bodied 90 rcsb build....

    This isn't 400 related but I finally finished the cam swap on my 04. Still needs a tune but sounds pretty beastly. She was loading up in this video. I've since regapped the plugs and it idled much better now. I actually put 100mi on it already and I think I had it shutoff once. Sent...
  7. 04silvy

    The never ending bagged and bodied 90 rcsb build....

    Tires are 255/35/20 in the front and 255/50/20 in the rear. I mounted up the two in the rear temporarily so I could set up the suspension to lay out on a similar tires size in 22". But ended up liking it so I just left them on. It nearly tucks lugnuts in the rear with these tires. Plus they...
  8. 04silvy

    Dylan's 89 c1500 scsb on going project.

    Wow ! Ya I knew it was a good deal..but damn. If I remember right he wanted $350-$400 and he had this story how it came out of his truck with 30k mi. When I got there it had the year and gear ratio written with a grease pencil so I knew it came from a scrap yard. Looked like it had been...
  9. 04silvy

    Dylan's 89 c1500 scsb on going project.

    Didn't even realize until now that you had a 454 SS rear. Good thing since your boosted. I was fortunate to find one as well...mine has 3.73s as well. I didn't really need a 14bolt but for $250 I couldn't have put gears or a posi in my 10bolt. Glad I bought it as things things are getting...
  10. 04silvy

    Dylan's 89 c1500 scsb on going project.

    Actually I think this is the same diagram that I used. Pretty much tells what all the pins are. I'll check tomorrow still what I have. Also if that's not what you need there is a few diagrams scattered through the pages of the Moonie swap thread. Here is the link...
  11. 04silvy

    blue_92_sierra's bagged ecsb build thread

    I agree completely about the traditional drop. I'm only 5'8" so I don't miss the headroom at all. I still would like to cut 2" or so out of the seat brackets to bring you down closer to stock....but never have gotten around to it. Btw no one can ever tell the truck is BD by looking inside...
  12. 04silvy

    Dylan's 89 c1500 scsb on going project.

    I think I still have some out in the garage actually. I'll see if I can scan it and upload it. I think they were wiring of a 90. It might be tomorrow before I can get to it though. Sent from my HTCONE using Tapatalk
  13. 04silvy

    blue_92_sierra's bagged ecsb build thread

    Yessss! Takes much bigger balls to cut up a nice truck like this opposed to one like mine...that was destined for the junkyard anyhow. This thing is going to be amazing bodied. You going traditional or stock floor with the cab? Sent from my HTCONE using Tapatalk
  14. 04silvy

    New project/tow pig

    It was post #8 but my eyes may be deceiving me. Lol. And I know what you mean..I've been unemployed going on a year now but seems like I still have 0 free time to work on anything. I did manage to order a cam ,springs and pushrods for the 04 almost a year after I said I was...lol Sent from...
  15. 04silvy

    The never ending bagged and bodied 90 rcsb build....

    Nothing really to report on updates other than that she's been in the garage for winter. Had a good aummer season and put 4k ish miles on it with no real problems to report. I have a vibration when laying into it I need to address. I think it's either the exhaust rattling on the tranny...
See more

Latest posts

Members online

... and 27 more.
Total: 1,812 (members: 77, guests: 1,735)

Forum statistics

Threads
64,457
Messages
1,394,530
Members
51,716
Latest member
Moesobs95

Share this page

Top