JPVortex's latest activity
-
JPVortex replied to the thread Bad running after manual swap.Yeah, I dont see how it could be anything else other than a short somewhere in its circuit. -
JPVortex replied to the thread Bad running after manual swap.I can try that, I did just replace the two that come from the ignition module to the coil with a junkyard connector, because I had...
-
JPVortex replied to the thread Bad running after manual swap.Yeah that’s what I think it is to be honest. It’s just weird that I cannot get it to do it on demand by moving the wires when it is...
-
JPVortex replied to the thread Bad running after manual swap.this is the most recent video of it. I’m so lost
-
JPVortex replied to the thread Bad running after manual swap.Yeah ignition problem still persists, I’m done chasing potential issues and I’ll leave it to the mechanic I’m bringing it to Wednesday.
-
JPVortex replied to the thread Bad running after manual swap.Will definitely investigate further if needed, BUT. I just picked up the acdelco spark plug wires. I took 2 and tested them and boy...
-
JPVortex replied to the thread Bad running after manual swap.I can check the resistance there, but I did just replace the whole dizzy with a new icm, cap, rotor etc like 3 days ago.
-
JPVortex replied to the thread Bad running after manual swap.None of them seemed to be an open circuit. Im going to go ahead and put 8 ACDelco's in there and see what happens. I also got a Delphi...
-
JPVortex replied to the thread Bad running after manual swap.Ok I’ve tested 6 NAPA wires, these are the results: 6,000 ohms/ft 7,000 ohms/ft 9,000 ohms/ft 10,000 ohms/ft 13,000 ohms/ft 9,000...
-
JPVortex replied to the thread Bad running after manual swap.Yeah these things are junk, they’re NAPA brand, I’ve tested all of them now. All over the board, most are 2-2 1/2ft long. I’m getting...
-
JPVortex replied to the thread Bad running after manual swap.Thank you, let me know what you get, deciding if I should get a new set of acdelco wires.
-
JPVortex replied to the thread Bad running after manual swap.I ohm tested a couple spark plug wires. They seem to be crazy high resistance. I had to set my ohm meter to read 200k because 20k was...
-
JPVortex replied to the thread Bad running after manual swap.So really even if a couple of the spark plug wires have enough voltage to escape the coil, if I had a good coil it won’t escape it no...
-
JPVortex replied to the thread Bad running after manual swap.Yeah I meant coil not distributor to answer your first question lol. And yeah I agree that it’s not all the cylinders. Probably one or...
-
JPVortex replied to the thread Bad running after manual swap.I suppose that could be it, I’m going to see what I can do tomorrow, but this truck may end up going to a shop for it. I feel like I...
Staff online
-
kennythewelderOfficially Retired, B31-3 (6-G) certified welder. -
df2x44L60E Destroyer
Members online
- El Coqui
- Cgbranch1
- dixiebandit69
- bluex
- 99xcss4
- washjoshburn
- BIGR
- gmcsean
- Brody
- Supercharged111
- Komet
- Orpedcrow
- BigBlueWhale
- kennythewelder
- Protegenoob17
- GoToGuy
- bob-a-lee
- Caman96
- Drunkcanuk
- df2x4
- DaltSmith94
- Canadian Rust Bucket
- isla bama
- kruznlow69
- JamesL7108
- Samuelvasquez44
- McDermott
- Deancr11
- sbduncan
- Badams7725
- dvbriski
- S_det
- amcfarlain3
- Jackslaw64
- jdaeromech
- Teriria
- Luftwaffles47
- Daly
- TX97z71
- scott2093
- Mg guy
- dieseldoesnt47
- Samcal
- paganfires817
- Phr0stByte
- Lowsport14
- Rgd88
- LemonySoda60432
- Alteca
- katwood16