Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Orpedcrow
Supporting Member
I don’t know what I’m doing
·
From
East Texas
Joined
Aug 20, 2022
Last seen
Today at 12:03 AM
Messages
2,552
Reaction score
6,485
Points
113
Find
Find content
Find all content by Orpedcrow
Find all threads by Orpedcrow
Latest activity
Postings
About
Orpedcrow
reacted to
fancyTBI's post
in the thread
3/4 Ton of fun - ‘95 Sierra
with
Like
.
Alignment scheduled with WCFab for Thursday. Will see how they do. I drove the truck more today. Parked it in the garage after and it...
Yesterday at 10:32 PM
Orpedcrow
reacted to
bluex's post
in the thread
1” front drop spring OBS extended cab
with
Like
.
No it doesn't if you don't do more than 1 coil. Lots of people trim the springs with no issues. Heating it is what really alters it an...
Yesterday at 9:32 PM
Orpedcrow
reacted to
Dravec's post
in the thread
My new project truck: '99 K2500 Suburban
with
Like
.
So, instead of doing a proper shake down run, we went and picked up the horse trailer that the fiancé scored for a surprisingly good...
Yesterday at 8:22 PM
Orpedcrow
reacted to
Dantheman1540's post
in the thread
Free to me GMC 2500
with
Haha
.
Tbh I got lost in the sauce over there. It was too much for a single morning poop reading session. I might have to revisit it. Anyone...
Yesterday at 7:27 PM
Orpedcrow
replied to the thread
Free to me GMC 2500
.
I think so but I can’t confirm. Have you been through the bucket seat alternatives sticky thread? There’s a tooon of information about...
Yesterday at 7:08 PM
Orpedcrow
reacted to
Dantheman1540's post
in the thread
Free to me GMC 2500
with
Like
.
I like the wrench! I’ll have to remove it and flip it over and look for a cable. Do you know if the motors can be replaced?
Yesterday at 7:07 PM
Orpedcrow
reacted to
Dantheman1540's post
in the thread
Free to me GMC 2500
with
Like
.
If only we were all smart enough to read pictures. The handle clearly shows sliding forward as well as tilting. So something internally...
Yesterday at 7:00 PM
Orpedcrow
replied to the thread
Free to me GMC 2500
.
I would think it would be cable actuated to release the slides when the seat is tilted forward. Of course comparing your picture to...
Yesterday at 7:00 PM
Orpedcrow
reacted to
Dantheman1540's post
in the thread
Free to me GMC 2500
with
Like
.
Lots of measuring and lots of using my digital angle finder and I think I got it setup right. I’ll find out when I go to bolt it in ...
Yesterday at 6:23 PM
Orpedcrow
replied to the thread
Free to me GMC 2500
.
The lower handle should lock the seat back into various positions and the upper handle should release the seat back, allowing it to...
Yesterday at 6:22 PM
Orpedcrow
replied to the thread
Free to me GMC 2500
.
My extended cab, manual 60/40, leans forward and slides with the rear egress handle. Both driver and passenger side.
Yesterday at 6:19 PM
Orpedcrow
reacted to
Dantheman1540's post
in the thread
Free to me GMC 2500
with
Like
.
That passenger side seat has the same handle and it does control both. Also the lower handle does the same thing as the upper handle...
Yesterday at 6:17 PM
Orpedcrow
reacted to
Dantheman1540's post
in the thread
Free to me GMC 2500
with
Like
.
Got the axle cleaned up today. Might do a bunch of measuring and get everything tacked into place even. I don’t have 220 in my shop so...
Yesterday at 6:15 PM
Orpedcrow
reacted to
Dantheman1540's post
in the thread
Free to me GMC 2500
with
Like
.
Ahh man, I ordered the bracket kit and was eyeing this super simple truss. Never done a truss on anything before. I know it’s totally...
Yesterday at 6:13 PM
Orpedcrow
reacted to
Dantheman1540's post
in the thread
Free to me GMC 2500
with
Like
.
Learning the hard way is always my favorite learning technique :anitoof: Interesting, I wonder what dash lights or other annoyances...
Yesterday at 6:12 PM
Loading…
Loading…
Latest posts
Lets see some dropped C1500s
Latest: OBSOkie
47 minutes ago
Lowered and Bagged Suspension
a/c diagnostic / repair
Latest: T1najero
58 minutes ago
Audio + Electronics
Brake booster rod adj.
Latest: RDF1
Today at 4:12 AM
Axles + Brakes
D
Frankenstein ? K2500 8600 gvw mismatched lower control arms
Latest: docstoy
Today at 2:58 AM
Stock Suspension + Bolt On Kits
Rats... need a new part
Latest: sactown
Today at 1:46 AM
Engine Performance + Maintenance
Staff online
df2x4
4L60E Destroyer
Members online
KleenScottsdale
89RCLB
89GMCJOHN
Oldsteel_chevy
termite
df2x4
porschetech
MurderYurFace
T1najero
strikk
DesertRat828
Duster
evilunclegrimace
Peavey
kakawyn
Ironjet
HazCat
toholdren
Chrimson85
b454rat
Carlaisle
Clammer
Forum statistics
Threads
64,777
Messages
1,400,327
Members
52,417
Latest member
Dman
Share this page
Facebook
X (Twitter)
Reddit
Pinterest
Tumblr
WhatsApp
Email
Share
Link
Members
Top