Well crap, Rad loosing water but I know what it is

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

kenh

"Sparkle someone else's eyes"
Joined
May 22, 2020
Messages
1,154
Reaction score
2,310
Location
rockwell, ia
I've noticed I've been loosing a little water. Basically emptied the reservoir in the last 6 months.

Installing a new idler arm today and noticed the bottom trans cooled line leaking. (fitting ON the radiator) HMMMM, grabbed a pliers and gave the nut a tweek and BAM! The nut pops off and water starts running out. PANIC!!! LOL

Is this part available? Part number? Maybe just red neck it with some gasket maker? It's my daily and right now nothing else to drive:banghead:


Ken
 

stutaeng

I'm Awesome
Joined
Aug 7, 2019
Messages
3,399
Reaction score
4,412
Location
Dallas, TX
The fitting broke off at the radiator? I can't remember if those years were plastic?

When I bought my truck with Vortec the PO had epoxied the main coolant hose nipple at the radiator side (plastic), and it was leaking...had to buy a new radiator.
 

kenh

"Sparkle someone else's eyes"
Joined
May 22, 2020
Messages
1,154
Reaction score
2,310
Location
rockwell, ia
No coolant and trans fluid are mixing. Half of the fitting goes in the plastic tank of the radiator and there is a nut on the outside to retain it in the tank with, I assume, an o-ring to seal it. The nut on mine is one of those thin stamped steel POS nuts. I have seen a "regular" aluminum nut on some.

My local O'reilly's said they had the part but it turned out to just be a flair fitting. Dorman P/N 800-755. I'm thinking I'm looking for a unicorn part that only comes with a radiator. Maybe a trip to the local pick a part is in order???

Oh hell that won't work because the cooler is on the back side of that fitting. Maybe I can just find a good aluminum nut to replace the steel one????

Ken
 

stutaeng

I'm Awesome
Joined
Aug 7, 2019
Messages
3,399
Reaction score
4,412
Location
Dallas, TX
Oh, snap!

My brother's 90 C1500 had a similar issue where the water and tranmission fluid mixed. He changed his radiator and drained his fluid, but his 700 went out in the end. Hopefully not your case.

After that incident he bypassed his radiator cooler because of the fear it would fail again in such manner.

Can you bypass it just to get it so you can drive it? Add an external cooler and flush out the entire old fluid.
 

kenh

"Sparkle someone else's eyes"
Joined
May 22, 2020
Messages
1,154
Reaction score
2,310
Location
rockwell, ia
The issue is not the cooler but with how the cooler is mounted to the radiator tank. The POS nut that captures the cooler will not hold tight. I'll get a photo and post it.

Ken

EDIT

The night steel nut slips on the threaded part of the cooler. Can't tighten it enough to stop the leak. I've see this style with a regular looking aluminum nut with more threads to grip. I think that will fix my issue. That or a new radiator

You must be registered for see images attach


You must be registered for see images attach
 
Last edited:

df2x4

4L60E Destroyer
Staff member
Moderator
Joined
Mar 1, 2012
Messages
11,563
Reaction score
14,120
Location
Missouri
You didn't mention what year the truck is, but if you do end up getting a new radiator be aware that many of the aftermarket replacements have a port under the fill cap which is only used on some of these trucks. If your particular truck doesn't use that port then I would take the time to find a replacement radiator that doesn't have it. Otherwise you'll need to source a good quality 5/8" silicone cap because it'll destroy standard rubber ones in a few months. Pic of the port in question...

You must be registered for see images
 

CrustyJunker

Is STILL Here?
Joined
May 20, 2012
Messages
774
Reaction score
963
Location
Indiana, USA
The radiator engine oil cooler fittings always weeped on my old truck, was lucky enough to never break them! I gave that thing 3 different brands of radiators in its life, and all behaved similarly after awhile.

Never actually leaked, but no matter how great I cleaned everything up, oil would eventually walk down the tubing.

Sorry to hear about the tough luck!
 
Last edited:

454cid

Sooper Pooper
Supporting Member
Joined
Sep 5, 2010
Messages
10,520
Reaction score
15,275
Location
The 26th State
I've noticed I've been loosing a little water. Basically emptied the reservoir in the last 6 months.

Installing a new idler arm today and noticed the bottom trans cooled line leaking. (fitting ON the radiator) HMMMM, grabbed a pliers and gave the nut a tweek and BAM! The nut pops off and water starts running out. PANIC!!! LOL

Is this part available? Part number? Maybe just red neck it with some gasket maker? It's my daily and right now nothing else to drive:banghead:


Ken

I assume you're talking about the large "nut" that looks like it's made of sheet metal? I think it's time to replace your radiator. Besides the nut, there should be a seal in there of some type. I've built radiotors, but never was exposed to the assembly of the ATF cooler inside the plastic tank, but I do know the cooler and it's attachment are the only thing plugging those holes. You could try something like epoxy temporarily, but a proper repair would be difficult at best, I think..... and really probably needs parts replaced, which aren't really serviceable at home. I paid to have a tank replaced on my OEM radoiator and it wasn't cheap, and only lasted a few more years. That cost didn't include a new oil cooler.
 

454cid

Sooper Pooper
Supporting Member
Joined
Sep 5, 2010
Messages
10,520
Reaction score
15,275
Location
The 26th State
The radiator engine oil cooler fittings always weeped on my old truck, was lucky enough to never break them! I gave that thing 3 different brands of radiators in its life, and all behaved similarly after awhile.

Never actually leaked, but no matter how great I cleaned everything up, oil would eventually walk down the tubing.

Sorry to hear about the tough luck!

That was probably the lines. The engine oil cooler lines are a known problem on our trucks.
 

HotWheelsBurban

Gotta have 4 doors..... Rawhide, TOTY 2023!
Joined
Sep 18, 2019
Messages
17,311
Reaction score
46,203
Location
Houston, Texas
I assume you're talking about the large "nut" that looks like it's made of sheet metal? I think it's time to replace your radiator. Besides the nut, there should be a seal in there of some type. I've built radiotors, but never was exposed to the assembly of the ATF cooler inside the plastic tank, but I do know the cooler and it's attachment are the only thing plugging those holes. You could try something like epoxy temporarily, but a proper repair would be difficult at best, I think..... and really probably needs parts replaced, which aren't really serviceable at home. I paid to have a tank replaced on my OEM radoiator and it wasn't cheap, and only lasted a few more years. That cost didn't include a new oil cooler.
When I had to replace the radiator in the Burb 3 years ago, it had a hairline crack in one of the tanks. The shop told me they could replace the tank for $160, or the whole radiator for $270. And that just replacing the tank was no assurance there wouldn't be continued problems with the radiator, since it was the original one. So I bit the bullet, paid some bills late, and had them do the whole radiator.
 

mattillac

Lurker
Joined
Jun 21, 2012
Messages
386
Reaction score
513
Had a really small antifreeze leak on mine a few years back, opposite side, leaking around that "thin stamped steel POS nut" for the oil cooler, at the (original/16yr old) radiator.

Upon closer inspection, it turns out mine was leaking (weeping) from what seemed like tiny little stress fractures (cracks) in the plastic radiator, just around the nut.

You must be registered for see images attach

You must be registered for see images attach


Best of luck.
 

454cid

Sooper Pooper
Supporting Member
Joined
Sep 5, 2010
Messages
10,520
Reaction score
15,275
Location
The 26th State
When I had to replace the radiator in the Burb 3 years ago, it had a hairline crack in one of the tanks. The shop told me they could replace the tank for $160, or the whole radiator for $270. And that just replacing the tank was no assurance there wouldn't be continued problems with the radiator, since it was the original one. So I bit the bullet, paid some bills late, and had them do the whole radiator.

I had mine done over a decade ago, and it was just over $100, if I recall correctly (just the tank fix, I did the rest). I think if it would have lasted more than just 2 or 3 years it would have been worth it, since I think radiators were more expensive then.... no Rockauto and I'm not sure if Amazon was into autoparts yet. The new tank held, but the engine oil cooler started leaking, and fouled my cooling system.

I still have that radiator sitting in the corner of my garage. I could probably use it again in a pinch, since I don't have the oil cooler hooked up anymore. I'd probably have to try soaking it, as I think it was starting to plug up, too.

I think what happens on the driver's side is that the hose bounces up and down and eventually stress cracks the plastic. The original tank on the orginal radiator and it's replacement both cracked there. I now have the upper hose zip-tied to the steel brace.
 

L31MaxExpress

Truly Awesome
Joined
Apr 21, 2018
Messages
10,956
Reaction score
18,938
Location
DFW, TX
Just change the radiator and save yourself future frustration. My stock radiator only made it to about 2008 and 70K or so. Plastic tank cracked under on of the the trans cooler nuts.
 

Erik the Awful

Truly Awesome
Air Force Supporting Member
Joined
Aug 9, 2019
Messages
10,036
Reaction score
23,517
Location
Choctaw, OK
Plus, the aluminum recyclers will give you a whole $2 right now for the core. It's worth it if you have a stack of a dozen radiator and condensors, 50 lbs of aluminum cans, and a set of nobody-wants-them 13" wheels.
 

SUBURBAN5

I'm Awesome
Joined
Jul 18, 2020
Messages
4,781
Reaction score
8,231
Location
Houston

Staff online

Forum statistics

Threads
78,049
Messages
1,644,157
Members
80,873
Latest member
Plumberj
Top