Idle issues

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Joe Dirte

I'm an idiot!
Joined
Dec 30, 2017
Messages
3,304
Reaction score
8,273
Location
Ahia
After a couple months of on n off problem chasin i got my 98 runnin with help of a lot of yall on here. My next issue is not too major. It'll sit n idle fine around 600 rpm but i put it in reverse last nite to move it (supposed to be storms today n i dont leave vehicles under these damn pines) and thr idle dropped n got a lil chuggin when tried to give it gas. No check engine lite. Rpms slowly picked back up and once i parked it idle came back to ~600. Im guessing that it may be a tooth off as if i free rev it has a slight hesitation. Figured id get some input since everyone here has led me in the right direction so far.

I did find this on another forum for use with torque pro app. Put it into the app for a new pid n when rain stops may try it out. Anyone ever seen this or know if this info is right?

You must be registered for see images attach


You must be registered for see images attach


You must be registered for see images attach


You must be registered for see images attach
 
Last edited:

L31MaxExpress

Truly Awesome
Joined
Apr 21, 2018
Messages
10,969
Reaction score
18,983
Location
DFW, TX
After a couple months of on n off problem chasin i got my 98 runnin with help of a lot of yall on here. My next issue is not too major. It'll sit n idle fine around 600 rpm but i put it in reverse last nite to move it (supposed to be storms today n i dont leave vehicles under these damn pines) and thr idle dropped n got a lil chuggin when tried to give it gas. No check engine lite. Rpms slowly picked back up and once i parked it idle came back to ~600. Im guessing that it may be a tooth off as if i free rev it has a slight hesitation. Figured id get some input since everyone here has led me in the right direction so far.

I did find this on another forum for use with torque pro app. Put it into the app for a new pid n when rain stops may try it out. Anyone ever seen this or know if this info is right?

You must be registered for see images attach


You must be registered for see images attach


You must be registered for see images attach


You must be registered for see images attach


You have to get the engine over 2,000 rpm for the CMR to be accurate. I prefer reading it as I open the throttle some at 2,000 rpm. During say a moderate throttle opening snap from 2,000-4,000 rpm. Read the value as the engine accelerates. I have set mine as much as +6° and not gotten a SES light. I set mine higher than spec because I run a bit more light throttle timing. I can get 48° of timing out of the distributor setup with the distributor set at +6. Set at Zero you can run 42° advance, once you get to 43-44° it will go to misfiring because it will fire the spark to the previous cylinder. With CNP these engines like as much as 52° of timing advance. Not sure why but mine always ran better at +6 when it was all stock so that is just where I set it over the years. I think it runs a little better advanced because it injects the fuel earlier and gives a little more time for the fuel to vaporize on the back of the hot intake valves before the valve opens.
 
Last edited:

Joe Dirte

I'm an idiot!
Joined
Dec 30, 2017
Messages
3,304
Reaction score
8,273
Location
Ahia
Got to take it for trip to town. Bout 8 mile round trip. Stumbles off the line n almost acts like old 4 bbl with secondaries kickin in. Cruises perfect excepr flashin CEL. Thibk it was still readin ~23 degrees advance while drivin n fluctuated between 10-23 with steady throttle.
 

Joe Dirte

I'm an idiot!
Joined
Dec 30, 2017
Messages
3,304
Reaction score
8,273
Location
Ahia
First pic is about 2-3000 rpm with quick rap to around 4000. 2nd is back to idle. Still chasin what feels like a misfire but cant find anything. 1000-2000rpm has a shake like a misfire. Still fallin on its face on take off.

You must be registered for see images attach


You must be registered for see images attach


You must be registered for see images attach


You must be registered for see images attach
 

Joe Dirte

I'm an idiot!
Joined
Dec 30, 2017
Messages
3,304
Reaction score
8,273
Location
Ahia
As an update i found my misfire. Pulled out #6 plug n had some fuel on it but still looked like it tried to fire a lil bit, just not as much as others. Tested spark from wire as it ran n spark would hit fast then stop then hit fast again. Started with cap. New MSD cap already had bunch of build up on tips inside after im gonna guess a total of 3 hrs runnin. Swapped for a delco cap. Seems to have helped but only slightly. Was a used cap after all but its still better. The miss is felt most around ~1750 rpm. Gonna order new Delco cap & rotor, and find the new coil i got somewhere around here. May even try a delco ICM as i believe the one on it is a parts store special. Guessin this is my flashing CEL issue (but no codes) as im cruisin with tach right there around 1500-2000. Wish me luck.
 

Forum statistics

Threads
78,135
Messages
1,645,637
Members
81,337
Latest member
1998SierraCCZ71
Top