Drill Bits...

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

97SWBCHEVY

OBS Enthusiast
Joined
Jun 9, 2021
Messages
94
Reaction score
49
Location
Texas
Just curious what brand of drill bits do y’all consider to be the best these days...something that doesn’t burn up as soon as you get started...it just seems like they just keep getting crappier and crappier these days compared to what you would get 15+ years ago...
Metal...like a truck frame as far as thickness etc...not going through any thick plate steel, or trying to drill out a hardened broke bolt out, or anything special...
I slow my drill down, I spray some lubricant while drilling a hole, etc...etc...etc...
I just want a decent set of drill bits 3/8th’s or so and down that will last a lil while...and if you’re gonna suggest a set of DeWalt drill bits don’t bother responding...lol
 

PlayingWithTBI

2022 Truck of the Year
Supporting Member
Joined
Jan 3, 2019
Messages
14,612
Reaction score
29,644
Location
Tonopah, AZ
My son has these and says they work better than any others he's tried.

Years ago we used cobalt bits on stainless and other hard surfaces. The only issue with them is they're brittle. If you catch one on a burr when breaking through, they'll break or chip the cutting edge off.
 

TechNova

I'm Awesome
Joined
Aug 11, 2018
Messages
694
Reaction score
957
Location
Wis
I buy only form Max Winters Drill Bit City for home and work. You have to call hi, he doesn't have online ordering.
Regardless of the bit you use, most people have trouble because they don't apply enough pressure. The heat needs to be carried away in the chips. You have to put enough straight pressure on the bit so it will cut a chip to remove the heat. A drill bit that rubs and doesn't cut heats the bit and ruins even the best bit. It can also damage a bit by predrilling a smaller size. Predrilling causes alot of pressure on the edge of the larger bit. The best way is a spot drill with a smaller size for location then go right to the finish size bit. I use some USA Fluid from Max but often use motor oil from squirt can.
 

thegawd

I'm Done!
Joined
Feb 29, 2020
Messages
2,260
Reaction score
4,297
Location
The Country Formerly Known as Canada!
I have every cobalt drill bit I'v ever had, up to half an inch. I do know how to sharpen drill bits and so I have a lot of assorted highspeed steel drill bits I just keep sharpening them but I have yet to sharpen a cobalt, a couple will need it soon or if I need them for steel. I needed to drill 27x8 1/4" holes in 3/8 steel plate that holds benches for a locker room because someone forgot to put holes on the official drawings FFS'S. anyways I bought every 1/4" drill bit the hardware store had anticipating a bunch of broken bits due to inexperienced helpers. but we didnt break one and only used 1 cobalt drill bit a piece. those are the ones that need some sharpening but are still working just fine.

I agree with everyone but @TechNova nailed it.... if your not producing perfect chips or 1 solid perfectly cut shaving then your not doing it right. I also agree with him that its not wise to step up drill bit sizes unless you want to ruin everyone of them. drill 1 small pilot hole if you must, I dont. I use a steel punch and hammer a center hole into it and then go for gold with the correct size final size drill bit. drill it once and be done. you dont even need oil as a lubricant.... Most of the time I dont want to waste it and only use water. generally setting the bit in a cup of water whenever it starts to get hot.

Al
 

TechNova

I'm Awesome
Joined
Aug 11, 2018
Messages
694
Reaction score
957
Location
Wis
there is the theory that water can cause hydrogen imbrittlement in the drill bit. I don't know if it is true, if not drilling dry, I use lube or oil. If doing many holes I tend to not drill dry since the bit heats up.
I have a farmer friend that argued that all drill bits are junk. I watched him drill some holes by hand, no pressure at first, would get frustrated then try to push hard after the cutting edge overheated. He would then break the bit from his frustrated pushing. He never could grasp the concepts.
 

thegawd

I'm Done!
Joined
Feb 29, 2020
Messages
2,260
Reaction score
4,297
Location
The Country Formerly Known as Canada!
ah interesting. I could see that happening. I however based that off of the coolant used in machining, it's mostly water so its not a concern of mine. but maybe what they mixed it with prevents that from happening.... IDK but good point. If I'm drilling over head or something like that, I load up a spray bottle with water or drill one tiny hole in a water bottle and spray that because I dont mind getting water everywhere when I might not want oil everywhere. I also dont really want to breath in oil fumes. plus you know when it comes to wood.... you dont want oil on it because it will never take a stain or hold paint and if it gets on a stain or paint its ruined. water generally is very easy to clean up. I'm a cabinet maker with lots of machine shop experience and always have water available.

Al
 
Last edited:

Erik the Awful

Truly Awesome
Air Force Supporting Member
Joined
Aug 9, 2019
Messages
10,038
Reaction score
23,542
Location
Choctaw, OK
Never used it but snap on over hear swears on the performance. Plus there lifetime warranty
I have a set of Snap-On bits I bought back when I was a tech. They're decent. "Lifetime warranty" doesn't mean as much if the Snap-On guy wants to whine and argue and be a pain in the butt whenever you try and get a tool replaced. The Harbor Freight cheapo cobalt bits I bought have worked better, but it may also be that I'm more experienced now. I buy the smaller bits in 10 packs from Amazon because they break. Just be sure and get cobalt or tungsten carbide.
 

Schurkey

For a pacifist, I sure am a radical mother...
Supporting Member
Joined
Jan 14, 2018
Messages
17,632
Reaction score
27,277
Location
The Seasonally Frozen Wastelands
Norseman brand.
I have a set of those. They're cut OK, except that they're thick-web, "split point" bits, and I hate thick webs and split points. Manufacturers often use thick webs to make up for using crappy steel. The steel is brittle, so without a thick web, the bit shatters easily. In other words, the thick web is a cost-cutting measure because they can cheapen the raw material.

My "good" bits are USA-made, HSS, thin-web Government-Surplus from decades ago. Properly sharpened, they cut like crazy. Sometimes, they break. And the ones that get used, are getting pretty short from resharpening.

Thick-web bits are stronger, so they take abuse better...but they're harder to push through the material. To sort-of make up for that, they sharpen them by splitting the point. Duplicating that when re-sharpening is hateful. And I've seen brand-new, factory-sharpened bits that have crappy geometry; they don't stand a chance at cutting properly.

For the record, I worked in a production environment for thirteen years. The Company sent out the dull drill bits to an outside contractor for re-sharpening. (Hundreds, if not thousands of bits at a time, and 11/64 was hugely popular.) The sharpening contractor did such a piss-poor job (Drill Doctor, or similar) that when we got the "sharpened" bits back, I'd have to put them against a bench grinder to make them cut. In other words, I could re-sharpen the bits by hand on a bench grinder and make them better than the "professionals" could resharpen them using a fixture and diamond wheels. (Dumbasses put no relief on the cutting edges, so the bit resisted going into the metal.) It got so bad that eventually the company quit resharpening bits smaller than a certain size--they just bought new ones. I've got five pounds of used, dull but otherwise OK smaller drill bits that someday I'll get around to sharpening, that I took home from that company. They were going in the dumpster otherwise.

SHI TTY CHINESE BITS ARE NEVER GOING TO CUT PROPERLY. The steel is no good. A proper sharpening gets them to cut nice...once. If the hole isn't too deep.

If you see drill bits that have a little "pilot" point on them, for Fo ok's sake don't buy them. They're a gimmick. Good luck resharpening them. They're junk drill bits with a fancy, factory-sharpened end that can't be duplicated. Use 'em once or twice, throw them in the recycle bin. Garbage.

IF (big IF) the steel is good, a drill bit can be sharpened to cut and to last...but thick webs make that a challenge. Not impossible, but not easy, either.

In my experience, drilling mild steel, broken bolts, etc--it matters less that the bits are "Titanium" coated; or Cobalt; or whatever Miracle Technology. The common stuff is made with cheap steel, thick webs and split points, and they don't work as well as a QUALITY HSS thin-web bit that's been sharpened properly with some relief on the cutting lips.




As others have said, don't sneak-up on the final hole size by drilling progressively larger. Select your final drill bit size. LOOK at the web of that bit. Select a pilot bit just a hint larger than the web. Drill the pilot hole, drill the hole "for real". Two steps--not five, or three, for any drilled hole likely found in automotive work.
 
Last edited:

Hipster

I'm Awesome
Joined
Mar 7, 2017
Messages
4,262
Reaction score
8,176
Location
Liberty, NC
"Wurth" brand bits is the best set I have. HSS German tool steel blah, blah, blah. They've lasted a long time. Cutting fluid helps.

There all kinds of guides out there about drilling speeds, bit sizes, and base metals your drilling.

Also not a fan of Drill Doctors or miracle coatings.

Buying cheap bits is akin to buying cheap striking tools. The proper metallurgy just isn't there.
 
Last edited:

MrPink

Bainisteoir Páirteanna
Joined
Jan 12, 2021
Messages
1,654
Reaction score
3,351
Location
Saginaw Mi
I use these in my home garage but when I was in a shop whether it were an autobody or mechanic shop I had Snap-on stuff. I still talk with my former snap-on guy but I haven't had to warranty a tool in a long time outside of the craftsman screw driver I broke a couple years ago and I have a 1/2" ratchet that is broken too sitting in my drawer.

 

thegawd

I'm Done!
Joined
Feb 29, 2020
Messages
2,260
Reaction score
4,297
Location
The Country Formerly Known as Canada!
I broke my first cobalt drill bit yesterday. it's a 3 pointed bit and I'm sure I could properly resharpen it. I was breaking the rules and drilling in a tight spot on an angle, frustrated trying to fix my 35 year old lawnmower deck. It is an Asian product.... it shattered. anyways it broke in a way that almost seemed like it was ment to, shorter and completely usable almost like it never broke! I drilled 2 more holes with it. :)

You must be registered for see images attach
You must be registered for see images attach
 

thegawd

I'm Done!
Joined
Feb 29, 2020
Messages
2,260
Reaction score
4,297
Location
The Country Formerly Known as Canada!
Schurkey, the shattered parts off that drill bit were without a doubt little weapons. the one rule I wasnt breaking was wearing safety glasses. the shards were all little spears waiting to penetrate skin or eyeballs. I always clean up the drill bit shavings so they dont end up in someone's feet, so I was able to get a good look at them. I didn't take any pics though.

these drill bits normally work wonderfully, just remember to wear your safety glasses!
 

Latest posts

Forum statistics

Threads
78,076
Messages
1,644,609
Members
81,185
Latest member
Alan9ari
Top